background image

18

EN

Cordless random orbital sander PESS 10-20V

8. Then turn the dust collector (

9

) clockwise to lock it in

place.

9

13

19

II.

I.

Cleaning / changing the filter insert of the dust collector

The filter insert has to be cleaned as soon as it is dirty. Check
the filter insert for dirt once or twice a year.
The filter insert should be exchanged in case of heavy soiling or
damage.

1. Remove the filter retainer with the filter insert from the

dust collector cover.

2. Clean the filter insert with warm water mixed with a

neutral cleaning agent.

3. Allow the filter insert to dry completely. Do not put a wet

filter insert into the dust collector!

4. Fit the filter retainer with the filter insert back into the dust

collector cover.

Disposal

The icon with the crossed-out waste bin on waste

electrical or electronic equipment stipulates that this equipment
must not be disposed of with the household waste at the end of
its life. You will find collection points for free return of waste
electrical and electronic equipment in your vicinity. The
addresses can be obtained from your municipality or local
administration. You can also find out about other return options
that apply for many EU countries on the website https://
hub.trotec.com/?id=45090. Otherwise, please contact an
official recycling centre for electronic and electrical equipment
authorised for your country.
The separate collection of waste electrical and electronic
equipment aims to enable the re-use, recycling and other forms
of recovery of waste equipment as well as to prevent negative
effects for the environment and human health caused by the
disposal of hazardous substances potentially contained in the
equipment.

Li-Ion

 In the European Union, batteries and accumulators must

not be treated as domestic waste, but must be disposed of
professionally in accordance with Directive 2006/66/EC of the
European Parliament and of the Council of 6 September 2006
on batteries and accumulators. Please dispose of batteries and
accumulators according to the relevant legal requirements.

Summary of Contents for 4450000031





















Reviews: