background image

EN

5

cross line laser BD7A

Technical data

Parameter

Value

Model

BD7A

Device dimensions
(length x width x height)

60 x 60 x 115 mm

Device weight

280 g

Multifunctional mount dimensions
(length x width x height)

125 x 81 x 220 mm

Multifunctional mount weight

189 g

Interfaces

Micro USB port for
charger

Range

10 m

Operating temperature

-20 °C to 50 °C

Storage temperature

-20 °C to 50 °C

Levelling duration

< 6 s

Laser output

< 1 mW (650 nm)

Laser accuracy

at 0°: ±0.8 mm/m
at ≤ 3°: ±1 mm/m

Laser class

2

Energy

Battery

Li-ion

Capacity

1000 mAh

Charging time

3 to 4 hours

Nominal voltage

3.7 V 

Operating time

approx. 5 hours of
continuous operation

Automatic switch-off

When the battery is low,
the levelling indicator
"NO Level" (9) flashes
for one minute before
the device turns off
automatically

Scope of delivery

1 x Cross line laser 

BD7A

1 x Multifunctional mount

1 x USB cable

1 x Manual

Transport and storage

Note

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Transport

The supplied Li-ion batteries are subjects to the requirements of
dangerous goods legislation.
Observe the following when transporting or shipping Li-ion
batteries:

The user may transport the batteries by road without any
additional requirements.

If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.

– Only ship batteries if their housing is undamaged.
– Please also observe any other national regulations.

For transporting the device use a suitable bag to protect it from
external influences.

Storage

When the device is not being used, observe the following
storage conditions:

dry and protected from frost and heat

protected from dust and direct sunlight

with a cover to protect it from invasive dust if necessary

The storage temperature is the same as the range given in
the Technical data chapter.

Summary of Contents for BD 7A











Reviews: