background image

EN

4

Operating manual – cordless glue gun PGGS 10-3,7V

Improper use

The device 

PGGS 10-3,7V

 is not suitable for bonding heat-

sensitive materials such as soft PVC, styrofoam and other
foams. The device 

PGGS 10-3,7V

 is not suitable for large-area

gluing.

Personnel qualifications

People who use this device must:

have read and understood the operating manual, especially
the Safety chapter.

Personal protective equipment

Wearing protective gloves.

They protect your hands from burns, crushing injuries
and skin abrasions.

Residual risks

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Warning of electrical voltage

Work on the electrical components must only be
carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug
of the charger from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.

Warning of explosive substances

Do not expose the battery to temperatures above 45
°C! Do not let the battery come into contact with water
or fire! Avoid direct sunlight and moisture. There is a
risk of explosion!

Warning of hot surface

The insertion tool might still be hot after the
application. Burn hazard when touching the insertion
tool.
Do not touch the insertion tool bare-handed!
Wear protective gloves!

Warning

Do not process materials containing asbestos.
Asbestos is considered carcinogenic.

Warning

Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the
hands of children.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Caution

Keep a sufficient distance from heat sources.

Notice

If you store or transport the device improperly, the
device may be damaged.
Note the information regarding transport and storage of
the device.

Information about the device

Device description

The device 

PGGS 10-3,7V

 is a cordless glue gun for repairs and

tinkering. The device is suitable for bonding wood, plastic,
textiles, cardboard, paper, ceramic, leather, cork, glass and
metal.
The battery level indication shows the charging status.
The automatic switch-off after 10 minutes helps you to save
energy during work breaks.
The device allows for a working time of 30 minutes. During a
work break, you can put the cordless glue gun down into the
charger.
The status LED indicates when the operating temperature has
been reached by a change of colour. The heating time is
60 seconds.
The ergonomically shaped handle and the light weight ensure
fatigue-free working.

Summary of Contents for PGGS 10-230V















Reviews: