background image

9

EN

Operating manual – cordless rotary hammer PRDS 10-20V

Observe the following when transporting or shipping Li-ion
batteries:

The user may transport the batteries by road without any
additional requirements.

If transport is carried out by third parties (e.g. air transport
or forwarding company), special requirements as to
packaging and labelling must be observed. This includes
consulting a dangerous goods specialist when preparing
the package.

– Only ship batteries if their housing is undamaged.
– Mask open terminals with tape and pack the battery in

a way that it cannot move inside the packaging.

– Please also observe any other national regulations.

Storage

Before

 storing the device, observe the following:

Switch off the device by setting the switch for clockwise/
counter-clockwise rotation to centre position (lock).

Hold onto the mains plug while pulling the power cable of
the charger out of the mains socket.

Allow the device to cool down.

Remove the battery from the device.

Remove the tool from the tool holder.

Clean the device as described in the Maintenance chapter.

For storing the device, use the transport case included in
the scope of delivery in order to protect the device from
external influences.

Do not store Li-ion batteries which are completely
discharged. Storing discharged batteries can lead to a
deep discharge and thus damage the battery.

When the device is not being used, observe the following
storage conditions:

dry and protected from frost and heat

ambient temperature below 40 °C

protected from dust and direct sunlight inside the transport
case

Start-up

Unpacking the device

Take the transport case out of the packaging.

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Check the contents of the transport case for completeness
and look for damages.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Dispose of the packaging material according to the
national regulations.

Charging the battery

Notice

The battery can be damaged in case of improper
charging.
Remove the charger's mains plug before inserting or
removing the battery.
Never charge the battery at ambient temperatures
below 10 °C or above 40 °C.

The battery is partially charged upon delivery to avoid damage
to the battery caused by a deep discharge.
Prior to initial start-up and when the battery is low (only the red
LED in the battery level indication (6a) is illuminated), the
battery should be charged. To do so, please proceed as follows:

1. Slide the battery (6) into the quick charger (12) upside

down.

15

16

1 h

12

6

6a

Summary of Contents for PRDS 10-20V



















Reviews: