Trotec PRDS 10-230V Original Instructions Manual Download

Page: 12 / 17

Operating manual – rotary hammer PRDS 10-230V

Selecting the operating mode

With the function selector switch (3) you can choose drilling /
hammer drilling or chiselling. Via the switch for the impact
mechanism (12) you either activate (hammer drilling or
chiselling) or deactivate (drilling) the impact mechanism.

Note
Only operate the function selector switch (3)
during operation!

Otherwise the device might be

damaged.

Note
Only operate the switch for the impact
mechanism (12) when the device is at a standstill!

Otherwise the device might be damaged.

1. Set the function selector switch (3) to the desired position.

The function selector switch comes with a safety lock that
has to be pushed in first, before you can change the switch
position.

2. Set the switch for the impact mechanism (12) to the

desired position.

Operating mode: Drilling

Operating mode: Hammer drilling

Summary of Contents for PRDS 10-230V


















Search results

Summary of Contents for PRDS 10-230V

Reviews:

Related manuals for PRDS 10-230V

Brands by name

Popular brands

Trotec PRDS 10-230V, Original Instructions Manual

Search results

Summary of Contents for PRDS 10-230V

Reviews:

Related manuals for PRDS 10-230V

Brands by name

Popular brands