background image

EN

4

Operating manual – rotary hammer PRDS 10-230V

Intended use

Only use the device 

PRDS 10-230V

:

for drilling in rock, wood, metal, ceramic and plastic

for hammer drilling in brick, concrete and rock

for chiselling in concrete, rock and plaster

whilst adhering to the technical data.
We recommend using the power tool with original Trotec
accessories.

Improper use

The device is not intended for drilling in natural stone.

Personnel qualifications

People who use this device must:

have read and understood the operating manual, especially
the Safety chapter.

Personal protective equipment

Wear protective headgear.

With it you protect your head from splintering, falling
and flying pieces which could cause injuries.

Wear hearing protection.

Excessive noise can lead to hearing loss.

Wear eye protection. 

With it you protect your eyes from splintering, falling
and flying pieces which could cause injuries.

Wear a protective mask.

It saves you from inhaling harmful dusts generated
when processing workpieces.

Wear tight-fitting protective clothing.

This protects you from the draw-in and entanglement
hazard posed by rotating parts.

Wear safety boots.

They protect your feet from splintering, falling and
flying pieces which could cause injuries.

Residual risks

Warning of electrical voltage

Electric shock from insufficient insulation.
Check the device for damages and proper functioning
before each use.
If you notice damages, no longer use the device.
Do not use the device when the device or your hands
are damp or wet!

Warning of electrical voltage

Work on the electrical components must only be
carried out by an authorised specialist company!

Warning of electrical voltage

Before any work on the device, remove the mains plug
from the mains socket!
Hold onto the mains plug while pulling the power cable
out of the mains socket.

Warning of electrical voltage

There is a risk of a short-circuit due to liquids
penetrating the housing!
Do not immerse the device and the accessories in
water. Make sure that no water or other liquids can
enter the housing.

Warning

Toxic dusts!
The harmful / toxic dusts produced during operation
pose of risk to the health of the operator and persons
in the vicinity.
Wear eye protection and a dust mask!

Warning

Do not process materials containing asbestos.
Asbestos is considered carcinogenic.

Warning

Make sure not to hit power, gas or water lines when
working with a power tool.
If necessary, use a pipe detector to check the wall you
want to drill in or slit open.

Warning

Dangers can occur at the device when it is used by
untrained people in an unprofessional or improper way!
Observe the personnel qualifications!

Warning

The device is not a toy and does not belong in the
hands of children.

Warning

Risk of suffocation!
Do not leave the packaging lying around. Children may
use it as a dangerous toy.

Warning

The tool holder must be firmly locked in place before
switching the device on, for an insufficiently or
incorrectly clamped accessory could be catapulted out
of the tool holder uncontrollably upon switch-on.

Summary of Contents for PRDS 10-230V


















Reviews: