background image

24

FOUR YEAR SUPREME WARRANTY:

For four years from date of retail purchase within Canada, MTD PRODUCTS LIMITED will, at its option, repair or 

replace, for the original purchaser, free of charge, any part or parts found to be defective in material or work-

manship. This warranty covers units which have been operated and maintained in accordance with the owner’s 

instructions furnished with the unit, and which have not been subject to misuse, abuse, commercial use, 

neglect, accident improper maintenance or alteration. Normal wear parts or components thereof are subject to 

special terms as noted below in the Ninety Day Consumer Warranty clause.
The engine, starter motor or component parts thereof carry separate warranties from their manufacturers. 

Please refer to the applicable manufacturer’s warranty policy for these items.

Ninety Day Consumer Warranty on Normal Wear Parts:

 All normal wear part failures will be covered on 

this product for a period of 90 days. After 90 days but within the four year warranty period, normal wear part 

failures will be covered if caused by defects in material or workmanship of other component parts.  Normal 

wear parts are defined as batteries, belts, blades, blade adaptors, grass bags, rider deck wheels, seats, tires and 

clutch parts (friction wheels).

Full Ninety Day Warranty on Battery (if equipped): 

 For ninety (90) days from the date of retail purchase, if 

any battery included with this unit proves defective in material or workmanship and our testing determines 

the battery will not hold a charge, MTD PRODUCTS LIMITED will replace the battery at no charge to the original 

purchaser.

Additional Limited Thirty Day Warranty on Battery (if equipped):

  After ninety (90) days but within one 

hundred twenty (120) days from the date of purchase, MTD PRODUCTS LIMITED will replace the defective 

battery, for the original purchaser, for a cost of one-half (½) of the current retail price of the battery in effect at 

the date of return.

Lifetime Warranty on Polymer Snow Discharge Chute: 

 If your product is a snow thrower equipped with 

a polymer snow discharge chute (the “Snow Chute”), and the Snow Chute fails, breaks, or malfunctions, the 

manufacturer will repair or replace the Snow Chute at no cost as long as it is still owned by the original pur-

chaser (or the original person for whom this product was purchased as a gift).  Control mechanisms attached 

to the Snow Chute, such as cables and control linkages, are covered under the other terms of this limited 

warranty, but are not covered by this paragraph (or beyond the normal applicable warranty period).  Except 

as specifically modified by this paragraph, all of the other terms, limitations, and conditions set forth in this 

document shall continue to apply to the Snow Chute.

Personal use:

 THE FOREGOING PARAGRAPHS CONSTITUTE THE MANUFACTURER’S ENTIRE WARRANTY WITH 

RESPECT TO ANY PRODUCT PURCHASED AND USED FOR PERSONAL FAMILY, HOUSEHOLD/RESIDENTIAL PUR-

POSES, AS DISTINGUISHED FROM COMMERCIAL USAGE.

Commercial use:

 ALL APPLICATIONS OTHER THAN PERSONAL USE AS OUTLINED ABOVE, ARE CONSIDERED 

COMMERCIAL USAGE.
New products purchased for commercial usage are warranted in the same manner and to the same extend 

EXCEPT the term of warranty will be 90 DAYS from date of purchase.

How to Obtain Service: 

 Warranty service is available, with proof of purchase, through your local MTD Autho-

rized Service Dealer.  If you do not know the dealer in your area, please write to the Service Department of MTD 

PRODUCTS LIMITED, P.O. BOX 1386, KITCHENER, ONTARIO N2G 4J1.  The return of a complete unit will not be 

accepted by the factory unless prior written permission has been extended by MTD PRODUCTS LIMITED.

Other Warranties:

  All other warranties, express or implied, including any implied warranty of merchantability 

is limited in its duration to that set forth in this express limited warranty.  The provisions as set forth in this 

warranty provide the sole and exclusive remedy of MTD PRODUCTS LIMITED obligations arising from the sale 

of its products.  MTD PRODUCTS LIMITED  will not be liable for incidental or consequential loss or damage.

5.10.11

Summary of Contents for 900 Series

























Reviews: