background image

9

Attaching The Steering Wheel 

If the steering wheel for your tractor did not come 
attached, the hardware for attaching it has been packed 
within the steering wheel, beneath the steering wheel 
cap. Carefully pry off the steering wheel cap and remove 
the hardware.
1. 

With the wheels of the tractor pointing straight 
forward

, place the steering wheel over the steering 

shaft.

2.  Place the washer (with the cupped side down) over 

the steering shaft and secure with the hex bolt. See 
Figure 3. 

3.  Place the steering wheel cap over the center of the 

steering wheel and push downward until it “clicks” into 
place.

Attaching The Seat

If the seat for your tractor did not come attached, follow 
the instructions below to attach it.

NOTE

: For shipping reasons, seats are either fastened 

to the tractor seat’s pivot bracket with a plastic tie, or 
mounted backward to the pivot bracket. In either case, 
free the seat form its shipping position and remove the 
two knobsfrom the bottom of seat before proceeding with 
applicable instructions below.

WARNING: Before operating this 
machine, make sure the seat is 
engaged in the seat stop, stand 
behind the machine and pull back 
on seat until fully engaged into 
stop.

Knob Adjustment Seat

1.  Position the shoulder screws (found on the base of the 

seat) inside the slot openings in the seat pivot bracket. 
Figure 4.

2.  Slide the seat slightly rearward in the seat pivot 

bracket, lining up the rear slots in the pivot bracket 
with the remaining two holes in the seat’s base. 

3.  Select desired position for the seat, and secure with 

the two knobs removed earlier. See Figure 4.

3

WARNING

Before operating 
this machine, make 
sure the seat is 
engaged in the seat 
stop, stand behind 
the machine and pull 
back on seat until 
fully engaged into 
stop.
Maximum tire 
pressure under any 
circumstances is 
30 psi. Equal tire 
pressure should be 
maintained at all 
times.

Setting Up 
Your Lawn 

Tractor

Figure 3

Figure 4

Tire Pressure

WARNING: Maximum 
tire pressure under any 
circumstances is 30 psi. 
Equal tire pressure should be 
maintained at all times.

The tires on your unit may be over-inflated for shipping 
purposes. Reduce the tire pressure before operating 
the tractor. Recommended operating tire pressure is 
approximately 10 p.s.i for the rear tires & 14 p.s.i. for the 
front tires. Check sidewall of tire for maximum p.s.i.

Summary of Contents for 77T Series

















































Reviews: