Troy-Bilt TB32CS, Operator'S Manual

4

• CORD SETS: Make sure your cord set is in good

condition, with a cord that is heavy enough to carry
the current that your unit will draw. An undersized cord
set will cause a drop in line voltage resulting in a loss
of power, as well as overheating. The table shown
above illustrates the correct size to use depending on
the cord length and nameplate amperage rating. If in
doubt, use the next heavier size line gauge. The
smaller the gauge number, the heavier the cord. To
prevent the cord from disconnecting from the unit, use
the cord hook shown in the Operating Instructions.

• Do not abuse the power cord. Do not pull or carry the

unit by the cord, use the cord as a handle, close a
door on the cord, or pull the cord around sharp edges
or corners. Keep the cord away from heated surfaces,
oil and sharp edges.

• Ground Fault Circuit Interrupter (GFCI) protection

should be provided on the circuit(s) or outlet(s) that will
be used for the unit. Use receptacles with built-in
GFCI protection for an extra measure of safety.

• A nameplate on your unit indicates the voltage used.

Never connect the unit to an AC voltage that differs
from this voltage.

• Inspect all extension cords and the unit power

connection periodically. Look closely for deterioration,
cuts or cracks in the insulation. Also inspect the
connections for damage. Repair or replace the cords if
any defects appear.

• Avoid dangerous environments. Never operate your unit

in damp or wet conditions. Moisture is a shock hazard.

• Do not use the unit in the rain.

• Do not handle the plug or the unit with wet hands.

WHILE OPERATING

• Wear safety glasses or goggles that are marked as

meeting ANSI Z87.1-1989 standards. Also wear
ear/hearing protection when operating this unit. Wear
a face or dust mask if the operation is dusty. Long
sleeve shirts are recommended.

• Wear heavy, long pants, boots and gloves. Do not

wear loose clothing, jewelry, short pants, sandals or
go barefoot. Secure hair above shoulder level.

• The cutting attachment shield must always be in place

while operating the unit. Do not operate unit without
both trimming lines extended, and the proper line
installed. Do not extend the trimming line beyond the
length of the shield.

• Adjust the D-handle to your size to provide the best grip.

Cord length (ft.)

25

50

100

150

Wire size (AWG)

16

16

16

14

MINIMUM WIRE SIZE FOR EXTENSION CORDS FOR

120 VOLT APPLIANCES USING 0-6 AMPS

• Be sure the cutting attachment is not in contact with

anything before starting the unit.

• Use the unit only in daylight or good artificial light.

• Avoid accidental starting. Do not carry around a unit

that is plugged in with your finger on the trigger switch.
Be sure the switch is in the off position when plugging
in the unit.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not overreach. Always keep proper footing and

balance.

• Always hold the unit with both hands when operating.

Keep a firm grip on all handles or grips.

• Keep hands, face, and feet at a distance from all

moving parts. Do not touch or try to stop the cutting
attachment when it is rotating.

• Do not operate the motor faster than the speed needed

to cut, trim or edge. Do not run the motor at high
speed when you are not cutting.

• Always stop the motor when cutting is delayed or

when walking from one cutting location to another.

• If you strike or become entangled with a foreign object,

stop the motor immediately and check for damage. Do
not operate before repairing damage. Do not operate
the unit with loose or damaged parts.

• Stop and switch the unit to off and unplug it during

maintenance, repair or cutting attachment
replacement.

• Use only genuine factory replacement parts when

servicing this unit. These parts are available from your
authorized service dealer. Do not use unauthorized
parts, accessories or attachments. Using unauthorized
parts may lead to serious injury, damage to the unit
and a voided warranty.

• Keep the unit clean of vegetation and other materials.

They may become lodged between the cutting
attachment and shield.

OTHER SAFETY WARNINGS

• Disconnect the unit from the power supply when it is idle,

when you are storing or transporting it, when you are
servicing it, and when you are changing attachments.

• Store the unit in a dry area, locked up to prevent

unauthorized use or damage, and stored in a high
place out of the reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean and free from debris.
Clean after each use. See the Cleaning and Storage
instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan someone this
unit, also loan them these instructions.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION