background image

TractionAir

23

Operating Tips

Compressor 

The truck compressor has a major influence over the successful operation 
of the TractionAir system; even a small amount of oil passing through the 
air system will have an adverse effect on the performance of not only the 
TractionAir pneumatics, but also the truck’s air brake system. 

Electronics 

TractionAir ECUs are non user-serviceable items and should only be repaired at 
the factory. Care must be taken when welding near the ECU or Pressure Cell. If 
possible, remove the 10 pin plug from the rear of the ECU first.

Do not tin wires with solder before inserting into screw terminals as the 

wire will then loosen in the terminals over time.

Filter Assembly - TAAF8 
Filter Element - TAAFE

The pneumatic system component of TractionAir G4 
is designed to cope better with the ingress of oil and 
other contaminants from the compressor and the truck’s 
air system, but is still susceptible to blockage from 
chunks of rubber and dirt coming back from the tyres. 
We recommend that the filter is opened and emptied at 
each service interval (six months).

Rotary Union - TADCCC & TADCHRHD

The TRT Extended Life rotator is a long service robust 
unit running carbon ceramic mechanical seal facings. 
This rotator minimises stand out of the wheel hub 
arrangement and is ideal for most applications.
80mm long by 57mm diam.

Important: Take care when pressure washing not to 

damage the rotators by forcing water into the bearings 

through the seal.

TADCCC

TADCHRHD

Summary of Contents for TractionAir





























Reviews: