background image

GDIM-26NT

GDIM-49NT

gdim

TRUE FOOD SERVICE EQUIPMENT, INC.

2001 East Terra Lane • O’Fallon, Missouri 63366-4434

(636)-240-2400 • FAX (636)-272-2408 • INT'L FAX (636)272-7546 • (800)-325-6152

Parts Department (800)-424-TRUE • Parts Department FAX# (636)-272-9471

Web: www.truemfg.com

CONGRATULATIONS! 

You have just purchased the finest commercial freezer available.  

You can expect many years of trouble-free operation.

TRUE

food

 

service

 

equipment

inc

.

INSTALLATION MANUAL

INSTALLATION MANUAL

gdim

 ‑ 

glass

 

door

 

ice

 

merchandisers

TABLE OF CONTENTS

#975541 • LM • 6/15

SAFETY INFORMATION

Safety Precautions  

1

Proper Disposal, Connecting Electricity, & Adapter Plugs  

2

INSTALLATION

Ownership, Uncrating, & How to Connect to Electricity  

3

Wire Gauge Chart  

4

Locating and Leveling  

4

Installation of Legs or Castors  

5

Sealing Cabinet to the Floor  

6

OPERATION

Startup  

7

Mechanical Temperature Controls Sequence of Operation  

8

MAINTENANCE, CARE, CLEANING

Cleaning Condenser Coil  

13

Important Warranty Information  

14

Stainless Steel Equipment Care and Cleaning  

15

General Maintenance  

16

WARRANTY

Warranty  

17

Summary of Contents for GDIM



















Reviews: