background image

............ www.truemfg.com ............

True Food Service Equipment, Inc.

2

2

2

2

SAFETY INFORMATION

PROPER DISPOSAL OF THE DISPLAY CASE

DANGER!

 

RISK OF CHILD ENTRAPMENT

USE OF EXTENSION CORDS

NEVER USE AN EXTENSION CORD! TRUE will not warranty any display case that has been connected to an extension cord 

(applies to cabinets ordered with optional 12" power cord).

Child entrapment and suffocation are not problems of 

the past. Junked or abandoned display cases are still dan-

gerous… even if they will sit for “just a few days.” If you 

are getting rid of your old display case, please follow the 

instructions below to help prevent accidents.

Before You Throw Away Your Old Display Case:

•  Take off the doors.
•  Leave the shelves in place so that children may not 

easily climb inside.

REPLACEMENT PARTS

•  Component parts shall be replaced with like components.

•  Servicing shall be done by authorized service personnel, to minimize the risk of possible ignition due to incorrect  

  parts or improper service.

•  Lamps must be replaced by indentical lamps only.

•  If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or  

  its service agent.

Summary of Contents for TCGD
















Reviews: