background image

The power cord of this appliance is equipped with
a 3-prong (grounding) plug which mates with a
standard 3-prong (grounding) wall outlet to mini-
mize the possibility of electric shock hazard from
this appliance.

Have the wall outlet and circuit checked by a quali-
fied electrician to make sure the outlet is properly
grounded.

If the outlet is a standard 2-prong outlet, it is your
personal responsibility and obligation to have it
replaced with the properly grounded 3-prong wall
outlet.

The refrigerator should always be plugged into it’s
own individual electrical circuit, which has a volt-
age rating that matches the rating plate. This
provides the best performance and also prevents
overloading building wiring circuits which could
cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the
power cord. Always grip plug firmly and pull
straight out from the outlet.

Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end.

When removing the refrigerator away from the wall,
be careful not to roll over or damage the power
cord.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
For personal safety, this appliance must be properly grounded.

WARNING!

USE OF ADAPTER PLUGS

NEVER USE AN ADAPTER PLUG!  Because of potential safety hazards under certain conditions, we
strongly recommend against the use of an adapter plug.

............ www.truemfg.com ............

............ www.truemfg.com ............

SAFETY INFORMATION

SAFETY INFORMATION

True Food Service Equipment, Inc.

True Food Service Equipment, Inc.

3

3

3

3

North America Use Only!

NEMA plugs

TRUE uses these types of plugs.

If you do not have the right outlet

have a certified electrician install

the correct power source.

Summary of Contents for TDBD-72-4


















Reviews: