background image

9

9

True Food Service Equipment, Inc.

............ www.truemfg.com ............

A. 

Before your new unit is connected to a power supply, 

check the incoming voltage with a voltmeter. If 

anything less than 100% of the rated voltage for 

operation is noted, correct immediately.

B. 

All units are equipped with a service cord, and must 

be powered at proper operating voltage at all times. 

Refer to cabinet data plate for this voltage.

TRUE 

requires that a sole use circuit be dedicated for the 

unit. Failure to do so voids warranty.

WARNING

Compressor warranties are void if compressor burns out 

due to low voltage. 

WARNING

Power supply cord ground should not be removed!

WARNING

Do not use electrical appliances inside the food storage

compartments of the appliances unless they are of the

type recommended by the manufacturer.

NOTE

To reference wiring diagram - Remove front louvered grill, 

wiring diagram is positioned on the inside cabinet wall.

ELECTRICAL INSTRUCTIONS

A. 

Set unit in its final location. Be sure there is adequate 

ventilation in your room. Under extreme heat 

conditions, (100°F+, 38°C+), you may want to install 

an exhaust fan.

WARNING

Warranty is void if ventilation is insufficient.

B. 

Proper leveling of your TRUE cooler is critical to 

operating success (for non-mobile models). Effective 

condensate removal and door operation will be 

effected by leveling.

C. 

The cooler should be leveled from inside the cabinet. 

Place a level on the inside floor of the unit front to 

back and side to side. 

D. 

Ensure that the drain hose or hoses are positioned in 

the pan.

E. 

Free plug and cord from inside the lower rear of the 

cooler (do not plug in).

F. 

The unit should be placed close enough to the 

electrical supply so that extension cords are never 

used.

WARNING

Cabinet warranties are void if OEM power cord is tampered 

with. TRUE will not warranty any units that are connected to 

an extension cord. 

LEVELING

INSTALLATION / OPERATION INSTRUCTIONS

Summary of Contents for TFP-48-18M-D-4































Reviews: