background image

1

1

True Food Service Equipment, Inc.

............ www.truemfg.com ............

SAFETY INFORMATION

•  This refrigerator must be properly installed 

and located in accordance with the Installation 

Instructions before it is used.

•  Do not allow children to climb, stand or hang on the 

shelves in the refrigerator. They could damage the 

refrigerator and seriously injure themselves.

•  Do not touch the cold surfaces in the refrigerator 

compartment when hands are damp or wet. Skin 

may stick to these extremely cold surfaces.

•  Do not store or use gasoline or other flammable 

vapors and liquids in the vicinity of this or any other 

appliance.

•  Keep fingers out of the “pinch point” areas; 

clearances between the doors and between the doors 

and cabinet are necessarily small; be careful closing 

doors when children are in the area.

NOTE

 

We strongly recommend that any servicing be preformed by 

a qualified individual.

•  Unplug the refrigerator before cleaning and  

 

  making repairs.
•  Setting temperature controls to the 0 position does 

not remove power.

•  Danger - Risk of fire or explosion. Flammable refrigerant used. Do not use mechanical devices to defrost 

refrigerator. Do not puncture refrigerant tubing.

•  Danger - Risk of fire or explosion. Flammable refrigerant used. To be repaired only by trained service personnel. 

Do not puncture refrigerant tubing. 

•  Caution - Risk of fire or explosion. Flammable refrigerant used. Consult repair manual/owner’s guide before 

attempting to service this product. All safety precautions must be followed.

•  Caution - Risk of fire or explosion. Dispose of properly in accordance with federal or local regulations. Flammable 

refrigerant used.

•  Caution - Risk of fire or explosion due to puncture of refrigerant tubing; follow handling instructions carefully. 

Flammable refrigerant used.

•  Caution - Keep clear of obstruction all ventilation openings in the appliance enclosure or in the structure for 

building-in.

WARNING!

Use this appliance for its intended purpose as described in this Owner Manual.

TO LOCATE REFRIGERANT TYPE, SEE SERIAL LABEL INSIDE CABINET.

This cabinet may contain fluorinated greenhouse gas covered by the Kyoto Protocol (please refer 

to cabinet’s inner label for type and volume, GWP of 134a= 1,300. R404a= 3,800).

For Hydrocarbon Refrigeration Only (R-290) See Below:

 How to Maintain Your TRUE Unit to Receive the Most Efficient and 

Successful Operation

You have selected one of the finest commercial refrigeration units made. It is manufactured under strict quality controls with 

only the best quality materials available. Your TRUE cooler when properly maintained will give you many years of trouble-

free service.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

Summary of Contents for TFP-48-18M-D-4































Reviews: