background image

............ www.truemfg.com ............

True Food Service Equipment, Inc.

1

1

SAFETY INFORMATION

•  This freezer must be properly installed and 

located in accordance with the Installation 
Instructions before it is used.

•  Do not allow children to climb, stand or hang on 

the shelves in the freezer.  They could damage 
the freezer and seriously injure themselves.

•  Do not touch the cold surfaces in the 

refrigerated compartment when hands are damp 
or wet.  Skin may stick to these extremely cold 
surfaces.

•  Do not store or use fammable liquids or vapours 

in the vicinity of this or any other appliance.

•  Keep fingers out of the “pinch point” areas; 

clearances between the doors and between 
the doors and cabinet are necessarily small; be    
careful closing doors when children are in the 
area.

NOTE: Any servicing, warranty repairs or maintenance 
should be carried out by qualified personnel, failure 
to do so could be dangerous and may invalidate your 
warranty.

•  Unplug the refrigerator before cleaning and    
 making 

repairs.

•  Setting temperature controls to 0 position does 

not isolate the unit from the electrical supply, 
you must disconnect the main power lead from 
the wall receptacle to isolate.

WARNING!

Use this appliance for its intended purpose as described in this Owner Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

How to Maintain Your              Unit 

to Receive the Most Efficient and 

Successful Operation

You have selected one of the finest commercial freezer units made.  It is manufactured under strict 

quality controls with only the best quality materials available.  Your TRUE freezer, when properly 

maintained, will give you many years of trouble-free service.

Summary of Contents for TMW-36F-QT














Reviews: