5
Lamp head types
The device can be used with three different lamp heads. Each lamp has a different function.
HR lamp
– The HR lamp is designed for hair removal.
SR lamp
– The SR lamp is designed to rejuvenate the skin.
AC lamp
– The AC lamp is designed to remove acne.
Replacing the lamp head
The device allows you to remove and replace the lamp head. Follow the instructions below.
1. Hold the lamp head and pull as
shown.
2. Insert the lamp head as shown.
AFTERCARE
− After epilating, you can safely apply lotion, cream, deodorant, moisturizer or other cosmetic
products to the treated area.
− If you experience skin irritation or redness after treatment, wait until these symptoms have
disappeared before applying any product to the skin. If you notice skin irritation or redness
after applying the product, rinse it with water.
− After epilating, we recommend not exposing the epilated area immediately to sunlight, or
to protect it with a product with a protective factor. It is also not advisable to visit tanning
booths and solariums within 24 hours after epilation.
DEVICE MAINTENANCE
− Maintaining this device ensures trouble-free operation and reduces the risk of damage.
− Keep the device away from extreme humidity and temperatures and do not expose the devi-
ce to direct sunlight or ultraviolet light for extended periods of time.
− Never use compressed air, scouring pads, abrasive or aggressive cleaning agents such as pe-
trol or acetone to clean the device.
− Do not expose the device to sudden and extreme changes in temperature. This can cause
moisture to condense inside the device, which could damage the device. In the event of
moisture condensation, allow the device to dry completely before using it again.
− Never attempt to disassemble, repair or modify the device in any way. Disassembly, modifi-
cation or any attempt at repair will void the warranty and may result in damage to the device
or even injury or property damage.
− Do not store or carry flammable liquids, gases, or explosive materials in the same place as the
device, its parts, or accessories.
− Overheating can damage the device.
CLEANING AND STORAGE
− After epilation, switch off the device and let it cool down. Be sure to unplug it. Inspect all
parts for damage and then wipe them with a cloth or other lint-free material - it can be slight-
ly damp. Do not wash or immerse the device in water or other liquids.
− Store the device in a dry place where it will not collect dust, at a temperature from 0°C to
40°C. Protect the treatment window and skin sensor from damage.
SIDE EFFECTS
− Depending on your skin type, using the device may be slightly uncomfortable. It may cause
some heat or reddening of the skin. This is a normal.
− Adverse reactions usually occur immediately after application or within 24 hours. In rare ca-
ses, they may appear later. If you get an unusual reaction, talk to your doctor.
TROUBLESHOOTING
If a malfunction occurs while using the device, follow the instructions below to find a solution.
If you do not find the answer to your problem here, please contact the manufacturer‘s customer
service.
Problem
Solution
Cannot start up.
Make sure the adapter is connected properly.
Flashes do not work.
Make sure that the light-emitting treatment window
is in contact with the skin properly and that the lights
are blue.
Constant blue indicator light.
Make sure that the lamp is not located in an area
where there are metal parts or the effects of inductive
capacity.
Device does not work in small areas.
Use the correct lamp head for small areas or areas that
are difficult to access. It is necessary to ensure that the
skin sensors are in contact with the skin.
Device is broken, cracked or does not
visually look right.
If you have any doubts about the safe use of the devi-
ce or damage to the device, do not use it and contact
the manufacturer.
The LCD display shows E0.
Something happened to the fan. After the device
cools down, turn it off and on again.
The LCD display shows E1.
Voltage problem. Contact the manufacturer.
The LCD display shows E2.
Improperly installed lamp head. Remove the lamp and
replace it according to the manual.