Truma BC 860 IU, Operation Instructions Manual

11

Accessories

Quickpower terminal clamps

For fast manual connection 

and release of the battery con-

nections. Suitable for all DIN 

and SAE connections  

(part no. C11000-02100). 

Temperature sensor for the battery I – MASTER –

Allows temperature-controlled battery charging.

Temperature sensor with a 

2 m connection cable and at-

tachment material  

(part no. C11000-00700).

Temperature sensor with a 

6 m connection cable and  

attachment material  

(part no. C11000-00800).

Charging control panel

Panel BC (430, 630, 860) for 

displaying the charging phas-

es, the parallel switching from 

the starter and supply battery 

and charging malfunctions in 

connection with the BC 630 IU 

automatic charger.

Panel BC (430, 630, 860) with 

7-pin control cable 5 m and  

attachment screws  

(part no. C14301-03).

Manufacturer’s terms of warranty

1. Case of warranty

The manufacturer grants a warranty for malfunctions in the 

appliance which are based on material or production faults. 

In addition to this, the statutory warranty claims against the 

seller remain valid.

A claim under warranty shall not pertain:

for parts subject to wear and in cases of natural wear and 

tear,

as a result of using parts that are not original Truma parts in 

the units,

as a consequence of failure to respect Truma instructions 

for installation and use,

as a consequence of improper handling,

as a consequence of improper transport packing.

2. Scope of warranty

The warranty is valid for malfunctions as stated under 

item 1, which occur within 24 months after conclusion of 

the purchase agreement between the seller and the final 

consumer. The manufacturers will make good such defects 

by subsequent fulfilment, i.e. at their discretion either by 

repair or replacement. In the event of manufacturers provid-

ing service under warranty, the term of the warranty shall not 

recommence anew with regard to the repaired or replaced 

parts; rather, the old warranty period shall continue to run. 

More extensive claims, in particular claims for compensatory 

damages by purchasers or third parties, shall be excluded. 

This does not affect the rules of the product liability law.

The manufacturer shall bear the cost of employing the Truma 

customer service for the removal of a malfunction under war-

ranty – in particular transportation costs, travelling expenses, 

job and material costs, as long as the service is carried out in 

Germany. The warranty does not cover customer service work 

in other countries.

Additional costs based on complicated removal and installa-

tion conditions of the appliance (e.g. removal of furniture or 

parts of the vehicle body) do not come under warranty.

3. Raising the case of warranty

The manufacturer's address is:  

Truma Gerätetechnik GmbH & Co. KG,

Wernher-von-Braun Strasse 12,

85640 Putzbrunn.

In Germany, always notify the Truma Service Centre if prob-

lems are encountered; in other countries the relevant service 

partners should be contacted (see Truma Service Booklet 

or www.truma.com). Any complaints are to be described in 

 detail. In addition, the properly completed guarantee certifi-

cate is to be presented, or the factory number of the unit and 

the date of purchase given.

To avoid transport damage, the device may only be dispatched 

after agreement with the Truma Service Centre in Germany or 

with the particular service partner concerned abroad. The risk 

for possible transport damage will otherwise be borne by the 

consignor.

If it is a case of warranty, the factory shall bear the cost for 

the delivery to the factory and the cost for returning the ap-

pliance to the customer. If the damage is deemed not to be 

a warranty case, the manufacturer shall notify the customer 

and shall specify repair costs which shall not be borne by the 

manufacturer; in this case, the customer shall also bear the 

shipping costs.

–

–

–

–

–