background image

4

ENGLISH

Safety Warnings

for the Use of Spray Guns

                          • The unit is designed to apply covering 

materials like paint, varnish, enamel, etc. These should 

have an ignition point not lower than 70 °F. Check the 

product can label or container.

                            • Do not spray substances you are not 

familiar with and if their potential danger is unknown to 

you.

                            • Do not spray flammable substances.

• Use care with dangers originated by the sprayed 

substances. Read the text and information in the cans and 

containers or the manufacturer specifications.

Substances and Materials

                          • The unit shall not be used in enclosed 

areas or explosive environments.

• If working outdoors consider wind direction. Wind carries 

the covering to great distances, causes damages and 

makes the job difficult.

                          • If working indoors, verify there is 

adequate ventilation.

                            • The work area shall be free of any 

ignition source.  Do not smoke while spraying or near the 

work area.

                          • Wear a face mask and safety goggles 

when spraying. Prevents damaging lungs and eyes.

• Wearing gloves and an overall is recommended to 

protect hands and clothes from the product when 

applying.

Before operating the unit

CAUTION

CAUTION

CAUTION

CAUTION

WARNING

WARNING

WARNING

                          • Never point the sprayer towards your 

body, passersby or animals.

• Make sure that the equipment does not absorb any 

steam solvent.

                          • In the event you need to pause during 

the application process, do not set the sprayer sideways. 

Hold it by the hook of somewhere for it be vertical.

While operating the device

                            • When finishing the job clean the gun 

perfectly to eliminate any product residue. Accumulations 

can damage the gun and cancel the Warranty

After operating the unit

CAUTION

CAUTION

WARNING

Summary of Contents for 14031





















Reviews: