background image

UNPACKING YOUR NEW LOW SPEED OR 

DUAL SPEED FLOOR MACHINE:

When your package is delivered, check each of the 3 

cartons carefully for signs of rough handling. If the 

LOW SPEED OR DUAL SPEED FLOOR MACHINE is 

damaged, notify the carrier immediately and request an 

inspection. Be sure to keep the cartons, packing inserts, 

packing lists and carrier’s receipt until the inspector has 

verified your claim.

CLEANFREAK.COM’s liability ceases when the carrier 

picks up the shipment. However, our customer service 

staff will be happy to furnish any information needed in 

connection with the claim and will attempt to expedite a 

resolution.

PLEASE READ BEFORE 

OPERATING YOUR NEW LOW SPEED OR 

DUAL SPEED FLOOR MACHINE:

Read the manual carefully and completely before at-

tempting to operate the unit. This manual has important 

information for the use and safe operation of the ma-

chine. Keep this manual handy at all times.

This equipment has been engineered and manufactured 

to provide excellent performance and service. To ensure 

that your equipment will continue to perform as intend-

ed:

•  Maintain and inspect equipment regularly.

•  Use only original CLEANFREAK.COM parts when 

servicing.

•  Operate equipment with care.

If additional information is needed, please contact 

CLEANFREAK.COM at: 888-722-5508    

All information and specifications printed in the manual 

are current at the time of printing; however, because of 

CLEANFREAK.COM’s policy of continual product im-

provement, we reserve the right to make changes at any 

time without notice.

FAILURE TO COMPLY WITH THE FOL-

LOWING WARNINGS AND INSTRUC-

TIONS WILL VOID THE WARRANTY.

WARNING!

 

 

•  Do not operate the machine unless trained and au-

thorized.

•  Do not leave the machine unattended when plugged 

in. Unplug from the outlet when not in use, before 

servicing, and when changing the brushes or pads.

•  Use indoors only.

•  Do not allow to be used as a toy. Close attention is 

necessary when used by or near children.

•  Do not bypass or defeat the safety “lock-out lever.”

•  The machine was designed for use as per instruc-

tions and recommendations written in this manual. 

Any deviation from its proper use or purpose and 

the consequential damage that may occur is the sole 

responsibility of the end user.

•  Do not use with damaged cord or plug. If the ma-

chine is not working as it should, or it has been 

dropped, damaged, left outdoors or dropped into 

water, take it to an authorized service center.

•  Do not pull or carry by cord, use cord as handle, 

close a door on the cord or pull cord around sharp 

edges or corners. Do not run machine over cord. 

Keep cord away from heated surfaces.

•  Do not unplug by pulling on cord. To unplug, grasp 

the plug, not the cord.

•  Do not handle plug or appliance with wet hands.

•  Make sure the machine is plugged into an electrical 

outlet with the same voltage and frequency rating 

as shown on the nameplate of the machine. Do not 

attempt to plug a 115- volt machine into a 230- volt 

outlet.

•  Do not immerse or use this machine in standing 

water. Such use can cause electric shock.

•  Keep the electrical supply cord from contacting the 

rotating brush or drive block.

•  Do not expose machine to freezing temperatures. 

•  To avoid electric shock, do not expose the unit to 

rain. Store indoors only.

•  Connect to a properly grounded outlet only. See 

“Grounding Instructions.”

•  Turn off all controls before unplugging.

•  When using an extension cord, use a 3 conductor-

grounding cord, 12 gauge wire or heavier. Do not use 

more than 25’ of extension cord.

•  Do not put any object into openings. 

2

Summary of Contents for TPL-BK-13-TC
















Reviews: