background image

  

iv 

Part Number 

1990142 / Revision H / August 2015 

Copyright 

©TSI Incorporated / November 1988

–2015 / All rights reserved. 

Address 

TSI Incorporated / 500 Cardigan Road / P.O. Box 64394 / St. Paul, MN  55164 / USA 

Fax No. 

(651) 490-3824  

E-mail Address 

fluid@tsi.com

  

Limitation of Warranty 
and Liability

 

(effective February 2015)

 

(For country-specific terms and conditions outside of the USA, please visi

www.tsi.com

.) 

Seller warrants the goods, excluding software, sold hereunder, under normal use and service 
as described in the operator's manual, to be free from defects in workmanship and material for 

12 months

, or if less, the length of time specified in the operator's manual, from the date of 

shipment to the customer. This warranty period is inclusive of any statutory warranty. This 
limited warranty is subject to the following exclusions and exceptions: 

a. 

Hot-wire or hot-film sensors used with research anemometers, and certain other 
components when indicated in specifications, are warranted for 90 days from the date of 
shipment. 

b. 

Parts repaired or replaced as a result of repair services are warranted to be free from 
defects in workmanship and material, under normal use, for 90 days from the date of 
shipment. 

c. 

Seller does not provide any warranty on finished goods manufactured by others or on 
any fuses, batteries or other consumable materials. Only the original manufacturer's 
warranty applies. 

d. 

This warranty does not cover calibration requirements, and seller warrants only that the 
instrument or product is properly calibrated at the time of its manufacture. Instruments 
returned for calibration are not covered by this warranty;   

f. 

This warranty is 

VOID

 if the instrument is opened by anyone other than a factory 

authorized service center with the one exception where requirements set forth in the 
manual allow an operator to replace consumables or perform recommended cleaning;   

g. 

This warranty is 

VOID

 if the product has been misused, neglected, subjected to accidental 

or intentional damage, or is not properly installed, maintained, or cleaned according to the 
requirements of the manual. Unless specifically authorized in a separate writing by Seller, 
Seller makes no warranty with respect to, and shall have no liability in connection with, 
goods which are incorporated into other products or equipment, or which are modified by 
any person other than Seller. 

 

The foregoing is 

IN LIEU OF

 all other warranties and is subject to the 

LIMITATIONS

 stated 

herein. 

NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR PARTICULAR 

PURPOSE OR MERCHANTABILITY IS MADE

WITH RESPECT TO SELLER’S BREACH OF 

THE IMPLIED WARRANTY AGAINST INFRINGEMENT, SAID WARRANTY IS LIMITED TO 
CLAIMS OF DIRECT INFRINGEMENT AND EXCLUDES CLAIMS OF CONTRIBUTORY OR 
INDUCED INFRINGEMENTS. BUYER’S EXCLUSIVE REMEDY SHALL BE THE RETURN OF 
THE PURCHASE PRICE DISCOUNTED FOR REASONABLE WEAR AND TEAR OR AT 
SELLER’S OPTION REPLACEMENT OF THE GOODS WITH NON-INFRINGING GOODS.

 

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER OR 
BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES, INJURIES, 
OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS BASED ON 
CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR OTHERWISE) SHALL BE THE 
RETURN OF GOODS TO SELLER AND THE REFUND OF THE PURCHASE PRICE, OR, 
AT THE OPTION OF SELLER, THE REPAIR OR REPLACEMENT OF THE GOODS. IN THE 
CASE OF SOFTWARE, SELLER WILL REPAIR OR REPLACE DEFECTIVE SOFTWARE 
OR IF UNABLE TO DO SO, WILL REFUND THE PURCHASE PRICE OF THE SOFTWARE. 
IN NO EVENT SHALL SELLER BE LIABLE FOR LOST PROFITS, BUSINESS 
INTERRUPTION, OR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR INCIDENTAL 
DAMAGES. SELLER SHALL NOT BE RESPONSIBLE FOR INSTALLATION, DISMANTLING 
OR REINSTALLATION COSTS OR CHARGES. No Action, regardless of form, may be 
brought against Seller more than 12 months after a cause of action has accrued. The goods 
returned under warranty to Seller's factory shall be at Buyer's risk of loss, and will be returned, 
if at all, at Seller's risk of loss. 

Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY AND 
LIABILITY, which contains the complete and exclusive limited warranty of Seller. This 
LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or its terms 
waived, except by writing signed by an Officer of Seller. 

Service Policy

 

Knowing that inoperative or defective instruments are as detrimental to TSI as they are to our 
customers, our service policy is designed to give prompt attention to any problems. If any mal-
function is discovered, please contact your nearest sales office or repre

sentative, or call TSI’s 

Customer Service at 1-800-874-2811 (USA) or (651) 490-2811. 

 

Summary of Contents for 9302














Reviews: