ｔｅｌｎｅｔ １９２．１６８．１．５５ ９９９９
NO 9999 is port set number of NCT08-02.
Click OK button and screen changed to telnet mode immediately.
ＭＡＣ ａｄｄｒｅｓｓ ００２０４Ａ８０Ｆ１Ｂ６
← It depends on the type of unit.
Ｓｏｆｔｗａｒｅ ｖｅｒｓｉｏｎ ０１．５（０３１００３）ＸＰＴＥ
← It depends on the type of unit.
Ｐｒｅｓｓ Ｅｎｔｅｒ ｔｏ ｇｏ ｉｎｔｏ Ｓｅｔｕｐ Ｍｏｄｅ
Push Return button in 3sec.
More than 3 sec, this connection is automatically cut off. Then try again from beginning.
Next display
・・・・・・
Ｃｈａｎｇｅ Ｓｅｔｕｐ：
０ Ｓｅｒｖｅｒ ｃｏｎｆｉｇｕｒａｔｉｏｎ
１ Ｃｈａｎｎｅｌ １ ｃｏｎｆｉｇｕｒａｔｉｏｎ
３ Ｅ－ｍａｉｌ ｓｅｔｔｉｎｇｓ
５ Ｅｘｐｅｒｔ ｓｅｔｔｉｎｇｓ
６ Ｓｅｃｕｒｉｔｙ
７ Ｆａｃｔｏｒｙ ｄｅｆａｕｌｔｓ
８ Ｅｘｉｔ ｗｉｔｈｏｕｔ ｓａｖｅ
９ Ｓａｖｅ ａｎｄ ｅｘｉｔ Ｙｏｕｒ ｃｈｏｉｓｅ ？
Then select 1.
Ｂａｕｄｒａｔｅ（３８４００）？
・・・・・ push return.
Ｉ／Ｆ Ｍｏｄｅ（４Ｃ）？
・・・・・ push return.
Ｆｌｏｗ（００）？
・・・・・ push return.
Ｐｏｒｔ Ｎｏ（７７７７）？
・・・・・enter port address of ｔｅｌｎｅｔ, then push return
（Default port NO is ７７７７, if you need to change this number,
recommended port number is 10000 to 10999.）
ＣｏｎｎｅｃｔＭｏｄｅ（Ｃ０）？
・・・・・ push return.
Ｒｅｍｏｔｅ ＩＰ Ａｄｄｒｅｓｓ：（０００）．（０００）．（０００）．（０００）・・・・・ push return three times.
Ｒｅｍｏｔｅ Ｐｏｒｔ （０）？
・・・・・ push return.
ＤｉｓＣｏｎｎＭｏｄｅ（００）？
・・・・・ push return.
ＦｌｕｓｈｕＭｏｄｅ （８０）？
・・・・・ push return.
Pack Cntrl (２０）？
・・・・・ push return.
ＤｉｓＣｏｎｎＴｉｍｅ（００：００）？ ・・・・・automatically power down set time when in no connection.
（set data is **:++ means **minutes and ++seconds）
(default data 00:00 means 5999s = 99min 59sec
ＳｅｎｄＣｈａｒ １ （０Ｄ）
・・・・・ push return.
ＳｅｎｄＣｈａｒ ２ （０Ａ）
・・・・・ push return.
Select 9, then finished setting works
Ｃｈａｎｇｅ Ｓｅｔｕｐ：
6/15
