background image

Copyright © 2019 TTA All Rights Reserved.

M4H Use Instruction

2

You can not fly it you are in drinking , tied, drugs, physical ,discomfort, etc. .

Please inspect it before using very time, including but not limited to parts of

fastness, organism and propeller of cracks, and abrasion ,battery ,the

effectiveness of light. When error happens, please stop using immediately

and replace the corresponding parts.

Abnormal working state of the UAV maybe happen accidentally, don’t open

the propellers and forcibly fly with wrong.

Do not try to prevent any moving parts while working.

1.2 Pesticide Usage

All pesticides are poisonous. Please be careful and work strictly according to the

safety instructions of pesticides.

When dispensing, please use clear water. If not, will cause jams mesh of

impurities. If it is blocked, please clear it before reuse

When dispensing , please note that liquid sparks and the pesticide residue in

fuselage will be harmful to human body.

When dispensing, please pay more attention and use protective tools, and do not

let body directly touch with the pesticides; After pesticide spraying, please clear

your skin, copter and remote control.

When using pesticide, there will be interaction between different pesticides , user

should clear cartridge or keep a certain interval time

Spraying shall be carried out in windless sunny day, don’t spray under high

temperature at noon. While breezing, the operator should be standing above the

wind and spraying; do not work when wind is four.

When spaying ,if you feel uncomfortable ,headache or dizzy, please leave the site

at once and rest. If once severe symptoms occur, immediately be sent to hospital.

Pesticide effect and the solution concentration, spray rate ,copter high from

crops ,wind direction, wind speed and so on are close related. When using

pesticide should consider the above factors, to achieve the best effect. Please

Summary of Contents for M4H




























































Reviews: