Nitro 275RS
-
Section 1 - Safety 1-5
Safety Training
1. Safety is the primary concern in the
design and manufacture of our products.
Unfortunately, our efforts to provide safe
equipment can be wiped out by a single
careless act of an operator or bystander.
2.
In addition to the design and configuration
of equipment, hazard control and accident
prevention are dependent upon the
awareness, concern, prudence and proper
training of personnel involved in the operation,
transportation, maintenance and storage of
this equipment.
3. It has been said, “The best safety feature
is an informed, careful operator.” We ask
that you to be that kind of operator. It is
the operator’s responsibility to read and
understand ALL safety instructions in the
manual and follow them. Accidents can be
avoided.
4. Working with unfamiliar equipment can lead
to careless injuries. Read this manual before
assembly or use, to acquaint yourself with
the machine. If this machine is used by any
person other than yourself, or is loaned or
rented, it is the machine owner’s responsibility
to make certain that the operator, prior to
using:
• Reads & understands the operator’s manual.
• Is instructed in safe and proper use.
5. Know your controls and how to stop the
engine and machine quickly in an emergency.
6. Train all new personnel and review
instructions frequently with existing workers.
Be certain only a properly trained and
physically able person will use the machinery.
A person who has not read and understood all
the safety instructions is not qualified to use
the machine. An untrained operator exposes
himself and bystanders to possible serious
injury or death. If the elderly are assisting with
the work, their physical limitations need to be
recognized and accommodated.
THINK SAFETY! WORK SAFELY!
Safety Signs
1. Keep safety signs clean and legible at all times.
2. Replace safety signs that are missing or have
become illegible.
3. Replaced parts that displayed a safety sign
should also display the current sign.
4. Safety signs displayed in Safety Sign Locations
each have a significant purpose and need to
be cleaned or replaced when necessary.
5. Safety signs are available from your authorized
distributor or dealer parts department or from
the manufacturer.
How to Install Safety Signs
1. Be sure that the installation area is clean and dry.
2. Be sure the temperature is above 10C (50F).
3. Determine the exact position of the new safety
sign before removing the paper backing.
4.
Align the sign over the specific area, carefully
press the sign on, slowly peeling away the
backing paper while smoothing the sign in
place.
5. Small air pockets can be pierced with a pin and
smoothed out using a piece of sign backing
paper.
Summary of Contents for Nitro 275RS
