Tüchler KABUKLIP Operating Manual Download

Page: 15 / 17

KabuKlip

Operating Manual v1.2 - Page 15/17

www.tuchler.net

June 2014

11.2.

Operation of the Kabuklip DMX Slave

Assignment of DMX Addresses to the Release Chains:

DMX

data

Chain 1

Chain 2

Chain 3

Chain 4

Chain 5

Chain 6

LED light

Base

address

Base

address

Base

address

Base

address

Base

address

Base

address

Base

address

Inactive/

Reset

Inactive/

Reset

Inactive/

Reset

Inactive/

Reset

Inactive/

Reset

Inactive/

Reset

9 …

247

Clamp

>247

Release

<128

Light off

>127

Light on

After the release, the chain can be reset by sending the DMX address <9 to the
respective chain.

STATUS LED:



Green



System OK



Red



DMX base address outside the permissible range

or no DMX signal

12.

Cessation of use, disassembly and disposal

When ceasing to use the system, disconnect it from the power supply at all poles and
secure it

agai

nst being switched back on.

When disposing of the system, separate



metals



plastic parts



electrical parts



lubricants

from each other.

Summary of Contents for KABUKLIP


















Search results

Summary of Contents for KABUKLIP

Reviews:

Related manuals for KABUKLIP

Brands by name

Popular brands

Tüchler KABUKLIP, Operating Manual

Search results

Summary of Contents for KABUKLIP

Reviews:

Related manuals for KABUKLIP

Brands by name

Popular brands