background image

 

 
 

 

65 42599 

ADAPTER, 

STRAIGHT 

66 

42600 

ADAPTER, SWIVEL 90 DEG. 

67 40146 

CAPSCREW 

68 21723 

NUT 

69 21106 

WASHER 

70 42283 

CAPLUG 

71 42517 

CAPSCREW 

72 42618 

ADAPTER, 

TEE 

73 42494 

HOSE 

ASSEMBLY 

74 42620 

ADAPTER, 

REDUCER 

75 

42033 

TEE, SWIVEL NUT 

76 41668 

CAPLUG 

77 42841 

O-RING 

78 

4101 

BUSHING & BREATHER 

79 32220 

PLUG 

80 42802 

GEAR 

HOUSING 

81 41641 

O-RING 

 
 

 
 
 

3 5 4 1 RL SU B-ASSEM BLY  BI LL OF M AT ERI AL 

 

SA-4217, INPUT GEAR SET (ITEM 8) 

ITEM DESCRIPTION 

QTY.  PART 

NO. 

8-1 INPUT 

CARRIER 1 

42838 

8-2 

INPUT PLANET GEAR 

42245 

8-3 PLANET 

PIN 3 

41760 

8-4 RETAINING 

RING 3 

41715 

8-5 PLATE 1 41769 
8-6 BEARING 3  30484 
8-7 RACE 6 28771 

 

SA-4215, OUTPUT GEAR SET (ITEM 60) 

 

ITEM DESCRIPTION 

QTY.  PART 

NO.

 

60-1 OUTPUT 

CARRIER 1 

42805 

60-2 PLANET 

GEAR 3 

42806 

60-3 PLANET 

PIN 3 

41747 

60-4 RETAINING 

RING 3 

41716 

60-5 BEARING 6  41717 
60-6 SPACER 3  41739 
60-7 RACE 6 939249

 

 

SA-4 2 1 8 , CABLE PACK ER (I T EM  6 4 ) 

 

ITEM DESCRIPTION 

QTY.  PART 

NO.

 

64-1 SPRING, 

L.H. 1 

42344 

64-2 CABLE 

PACKER 1 

42840 

64-3 SPRING, 

R.H. 1 

42343 

 

 

15 

Summary of Contents for Rufnek Intelliguard 3541RL



















Reviews: