Tunturi Cardio Fit T35, User Manual

2 0

GB

Cleaning and maintenance

 ⚠ WARNING

•  Your trainer requires monthly maintenance, even when not 

being used� 

•  Before cleaning and maintenance, remove the mains plug from 

the wall socket�

•  Do not use solvents to clean the equipment�

- Do not block the ventilation openings� Keep the ventilation 

openings clear from dust, dirt and other obstructions�

- Clean the equipment with a soft, absorbent cloth after each use�

- Clean the visible parts of the equipment with a vacuum cleaner 

with a small suction nozzle

- Regularly check that all screws and nuts are tight�

 ⚠ CAUTION

•  We recommend to use indoor shoes only on your treadmill� 

When you don’t have these we do recommend to check the 
soles of your footwear before using them on your treadmill�  
The treadmill is not sustainable for dirt from outdoors�

General Cleaning

Dirt, dust, and pet hair can block air inlets and accumulate on the 
running belt� On a monthly basis: vacuum underneath your treadmill 
to prevent build-up� 
UNPLUG POWER CORD BEFORE THIS TASK�

Belt Dust

This occurs during normal break-in or until the belt stabilizes� Wiping 
off excess dust with a damp cloth will minimize build-up�

Belt and Running Deck

Your treadmill uses a very high-efficient low-friction bed�  
Performance is maximized when the running deck is kept clean and 
free from dust and dirt� Dirt and dust particles between running deck 
and running belt will damage your running deck surface affecting 
your performance and product lifetime�

How to clean running deck

Use a soft, dry, non-abrasive cloth to wipe the edge of the belt and 
the area between the belt edge and frame� try to reach under the 
running belt edges too, to remove the dirt build up on the edges too�

How to clean running belt surface

Firstly use a nylon scrub brush to remove the loose particles from the 
running belt surface� Than use wrung out damp cloth (no cleaners or 
abrasives) to gentle clean the top of the textured belt� Allow the belt 
to fully dry before using�

  ‼  NOTE

•  When your belt too dirty to clean with water only, you can use a 

mild soap, but never a lubricant solvent�

•  Prevent that the solution comes between running deck and 

running belt at all times� 

This should be done on a regular basis to extend belt and running 
deck life�

Lubrication (fig. F-6)

 ‼  NOTE

•  The Treadmill running belt is pre lubricated before fitting on 

your treadmill during the production of the unit� Therefore it is 
not needed to lubricate the running belt when taken into use for 
the first time� 

The running belt must be checked for lubrication condition regularly� 
Therefore the treadmill comes with a 300 hours reminder function� 
The “TIME WINDOW” will display “OIL” and will make an acoustic 
beeping sound every 10 seconds to remind you� Follow the below 
checking procedure and eliminate the “OIL” message and acoustic 
warning signal by pressing and hold the “STOP” button for at least 3 
seconds during this warning signal�

 ⚠ WARNING

•  Before lubrication, remove the mains plug from the wall socket�

 ⚠ CAUTION

•  We recommend to check the running belt lubrication at least 

once every month, as more factors than time can be effective to 
the lubricant conditions�

•  Only lubricate the running belt if necessary� If you apply too 

much lubricant, the running belt will slip easily due to lack of 
friction�

- Stand steadily on the running belt�

- Take hold of the front handlebar and push the running belt with 

your feet so that it slides back and forth� The running belt must 
move smoothly and evenly without making sound�

- If the running belt does not move smoothly and evenly or if the 

running belt does not move at all, touch the underside of the 
running belt with your fingertips to check the lubrication:

•  If you feel lubrication or your fingertips are shiny, there is 

sufficient lubrication on the running belt�

•  If you do not feel lubrication or your fingertips are dusty or 

rough, apply lubricant (±10 ml�) in the middle of the running 
deck under the running belt and let the equipment operate at 
5km/h for at least 5 minutes�

•  After lubrication, do not fold the equipment before having done 

a workout for 2 minutes with a speed of at least 5 km/h�  
This will cause the lubricant being fully absorbed by the running 
belt and being spread evenly�

‼  NOTE

•  When 5 km/h is too fast for you, do walk at your desired speed, 

but extend the duration to at least 5 minutes� 

Click to see our supportive YouTube video
https://youtu�be/ceaOYnofY5k

Belt adjustments

The performance of your treadmill is dependent on the frame running 
on a reasonably level surface� If the frame is not level, the front and 
back roller cannot run parallel, and constant belt adjustment may be 
necessary�

The treadmill is designed to keep the running belt reasonably centred 
while in use� It is normal for some belts to drift near one side while 
the belt is running with no one on it� After a few minutes of use, 
the running belt should have a tendency to centre itself� If, during 
use, the belt continues to move toward one side, adjustments are 
necessary�