Tunturi FitRun 30, User Manual

2 0

English

The warranty does not cover defects arising from  the 

failure to carry periodic  maintenance as outlined within 

the Owner’s Manual for the product. Furthermore, the 

warranty does not cover defects arising from usage and 

storage within an unsuitable environment as described 

within the Owner’s Manual which should be indoors, 

dry, dust and grit free and within a temperature range 

of  +15°C to +35°C. The warranty does not cover 

maintenance activities, such as cleaning, lubricating, 

and normal part adjustments, nor installation 

procedures that customers can accomplish  themselves, 

such as changing uncomplicated meters, pedals and 

other similar parts not requiring any dismantling/

reassembling of the fitness equipment. Warranty 

repairs carried out by other than authorised Tunturi 

representatives are not covered. 

Failure to follow the instructions given in the Owner’s 

Manual will invalidate the product’s warranty.

Cleaning and maintenance

WARNING

• 

Before cleaning and maintenance, remove the 

mains plug from the wall socket.

• 

Do not use solvents to clean the equipment.

-

Do not block the ventilation openings. Keep the 

ventilation openings clear from dust, dirt and other 

obstructions.

-

Clean the equipment with a soft, absorbent cloth 

after each use.

-

Clean the visible parts of the equipment with a 

vacuum cleaner with a small suction nozzle

-

Regularly check that all screws and nuts are tight.

Belt and Running Deck 

Your treadmill uses a very high-efficient low-friction 

bed. Performance is maximized when the running deck 

is kept as clean as possible. Use a soft, damp cloth or 

paper towel to wipe the edge of the belt and the area 

between the belt edge and frame. Also reach as far as 

practical directly under the belt edge. This should be 

done once a month to extend belt and running deck 

life. Use water only - no cleaners or abrasives. A mild 

soap and water solution along with a nylon scrub brush 

will clean the top of the textured belt. Allow the belt to 

dry before using.

Lubrication (fig. F-4)

The running belt must be checked for lubrication once 

per 2 months, based on the average use of 60 minutes 

per day.

WARNING

• 

Before lubrication, remove the mains plug from the 

wall socket.

CAUTION

• 

Only lubricate the running belt if necessary. If you 

apply too much lubricant, the running belt will slip 

easily due to lack of friction.

-

Stand steadily on the running belt.

-

Take hold of the front handlebar and push the 

running belt with your feet so that it slides back and 

forth. The running belt must move smoothly and 

evenly without making sound.

-

If the running belt does not move smoothly and 

evenly or if the running belt does not move at all, 

touch the underside of the running belt with your 

fingertips to check the lubrication:

• 

If you feel lubrication or your fingertips are shiny, 

there is sufficient lubrication on the running belt.

• 

If you do not feel lubrication or your fingertips are 

dusty or rough, apply lubricant (15-20 ml) in the 

middle of the running deck under the running belt 

and let the equipment operate at 5km/h for at least 

5 minutes.

• 

After lubrication, do not fold the equipment before 

having done a workout for 20 minutes with a speed 

of at least 5 km/h. The lubricant will be spread 

evenly over the running belt.

Belt Dust

This occurs during normal break-in or until the belt 

stabilizes. Wiping excess off with a damp cloth will 

minimize build-up.

General Cleaning

Dirt, dust, and pet hair can block air inlets and 

accumulate on the running belt. On a monthly basis: 

vacuum underneath your treadmill to prevent buildup. 

Twice a year, you should remove the black motor hood 

and vacuum out dirt that may accumulate. 

UNPLUG POWER CORD BEFORE THIS TASK.

Belt adjustments

Adjustment must be made from the rear roller. The 

adjustment bolts are located at the end of the step rails 

in the end caps.

-

Tighten the rear roller bolts (clockwise) only enough 

to prevent slippage at the front roller. Turn both 

running belt tension adjustment bolts in increments 

of 1/4 turn each and inspect for proper tension by 

walking on the belt at a low speed, making sure the 

belt does not slip. Keep tensioning the bolts until 

the belt stops slipping.

-

If you feel the belt is tight enough, but it still slips, 

the problem may be a loose Motor drive belt under 

the front cover.

-

Do Not Over-tighten

Over tightening will cause belt damage and 

premature bearing failure.