1 8
English
Use
Adjusting the support feet
The equipment is equipped with 4 support feet. If
the equipment is not stable, the support feet can be
adjusted.
-
Turn the support feet as required to put the
equipment in a stable position.
-
Tighten the lock-nuts to lock the support feet.
NOTE
-
The machine is the most stable when all support
feet are turned fully in. Therefore start to level the
machine by turning all support feet fully in, before
turning out the required support feet to stable the
machine. .
Adjusting the vertical seat position
The vertical seat position can be adjusted by setting the
seat tube to the required position. With the leg almost
straight, the arch of the foot must touch the pedal at its
lowermost point.
-
Loosen the seat tube adjustment knob.
-
Move the seat tube to the required position.
-
Tighten the seat tube adjustment knob.
Adjusting the horizontal seat position
(fig. E-2)
The horizontal seat position can be adjusted by setting
the seat to the required position.
-
Loosen the quick release lever under the seat.
-
Slide the seat forward or backward as desired.
-
Tighten the quick release lever.
Adjusting the handlebar
The handlebar can be adjusted according to the height
and the exercise position of the user.
-
Loosen the handlebar adjustment knob.
-
Move the handlebar to the required position.
-
Tighten the handlebar adjustment knob.
Power supply (Fig. E-1)
The trainer is powered by an external power supply.
Refer to the illustration to locate the trainer power
input.
NOTE
• Connect the power supply with the trainer
before connecting it to the wall outlet.
• Always remove power cord when
• machine is not in use.
Console (fig F)
1
3
2
1. Display
2. Tablet/ book support
3. Buttons
CAUTION
• Keep the console away from direct sunlight.
• Dry the surface of the console when it is covered
with drops of sweat.
• Do not lean on the console.
• Only touch the display with the tip of your finger.
Make sure that your nails or sharp objects do not
touch the display.
NOTE
• The console switches to standby mode when the
equipment is not used for 4 minutes.
Explanation Display functions
Time
-
Without setting the target value, time will count up.
-
When setting the target value, time will count down
from your target time to 0 and alarm will sound or
flash.
-
Without any signal being transmitted into the
monitor for 4 seconds during workout, time will
STOP
-
Range 0:00~99:59
Speed
-
Displays current training speed.
Maximum speed is 99.9 KM/H or ML/H.
-
Without any signal being transmitted into the
monitor for 4 seconds during workout, SPEED will
display “0.0”
Summary of Contents for Star Fit E100 HR i
