Tunturi T20 User Manual Download

Page: 22 / 102

2 2

‼ NOTE

• Incline setting is not controlled in HRC program mode but

can be controlled by user at any time to intensify or ease your
workout.

• Speed can be changed by user at all times.
• When speed is over the pre set speed limit it will auto adjust to

pre set speed setting automatically.

• If no heart rate is detected, the treadmill will stop workout.

⚠ CAUTION

• Heart rate measurement is required for this function.

ERP Function

ERP function can shut your treadmill in sleep mode automatically
when being without operation for 4:30 minutes.
You can turn this function On and off by:

- When treadmill is in “start up mode” press and hold “Mode”

button for 3 seconds to switch between On and Off mode.

• Display shows “1111” indicates On mode.

Machine will turn to sleep mode after 4:30 minutes being idle.

• Display shows “2222” indicates Off mode.

Machine will not turn into sleep mode after 4:30 minutes being
idle.

⚠ CAUTION

• We recommend to set ERP function in On mode always.

Bluetooth & APP

- This console can connect with an APP on a smart device by

Bluetooth (iOS & Android).

- Establish the Bluetooth connection only via the connection mode

on the installed APP on your smart device.

‼ NOTE

• Tunturi only provides the option to connect your fitness console

throughout a bluetooth connection. Therefore Tunturi cannot
be held responsible for damage, or malfunctioning of products
other than Tunturi products.

• Check the website for extra information.

Cleaning and maintenance

⚠ WARNING

• Your trainer requires monthly maintenance, even when not being

used.

• Before cleaning and maintenance, remove the mains plug from

the wall socket.

• Do not use solvents to clean the equipment.

- Do not block the ventilation openings. Keep the ventilation

openings clear from dust, dirt and other obstructions.

- Clean the equipment with a soft, absorbent cloth after each use.

- Clean the visible parts of the equipment with a vacuum cleaner

with a small suction nozzle

- Regularly check that all screws and nuts are tight.

⚠ CAUTION

• We recommend to use indoor shoes only on your treadmill.

When you don’t have these we do recommend to check the
soles of your footwear before using them on your treadmill.
The treadmill is not sustainable for dirt from outdoors.

General Cleaning

Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis: vacuum underneath your treadmill
to prevent build-up.
UNPLUG POWER CORD BEFORE THIS TASK.

Belt Dust

This occurs during normal break-in or until the belt stabilizes. Wiping
off excess dust with a damp cloth will minimize build-up.

Belt and Running Deck

Your treadmill uses a very high-efficient low-friction bed.
Performance is maximized when the running deck is kept clean and
free from dust and dirt. Dirt and dust particles between running deck
and running belt will damage your running deck surface affecting
your performance and product lifetime.

How to clean running deck

Use a soft, dry, non-abrasive cloth to wipe the edge of the belt and
the area between the belt edge and frame. try to reach under the
running belt edges too, to remove the dirt build up on the edges too.

How to clean running belt surface

Firstly use a nylon scrub brush to remove the loose particles from the
running belt surface. Than use wrung out damp cloth (no cleaners or
abrasives) to gentle clean the top of the textured belt. Allow the belt
to fully dry before using.

‼ NOTE

• When your belt too dirty to clean with water only, you can use a

mild soap, but never a lubricant solvent.

• Prevent that the solution comes between running deck and

running belt at all times.

This should be done on a regular basis to extend belt and running
deck life.

Lubrication (fig. F-6)

‼ NOTE

• The Treadmill running belt is pre lubricated before fitting on your

treadmill during the production of the unit. Therefore it is not
needed to lubricate the running belt when taken into use for the
first time.

The running belt must be checked for lubrication condition regularly.
Therefore the treadmill comes with a 300 hours reminder function.
The “TIME WINDOW” will display “OIL” and will make an acoustic
beeping sound every 10 seconds to remind you. Follow the below
checking procedure and eliminate the “OIL” message and acoustic
warning signal by pressing and hold the “STOP” button for at least 3
seconds during this warning signal.

⚠ WARNING

• Before lubrication, remove the mains plug from the wall socket.

⚠ CAUTION

• We recommend to check the running belt lubrication at least

once every month, as more factors than time can be effective to
the lubricant conditions.

• Only lubricate the running belt if necessary. If you apply too

much lubricant, the running belt will slip easily due to lack of
friction.