background image

14

15

Sicherheitshinweise

Der  DOC Skimmer  9460  ist  für  den  Betrieb  im  Freien 

nicht zulässig (1).

Vor Inbetriebnahme prüfen, ob die Betriebsspannung mit 

der Netzspannung übereinstimmt.

Um Wasserschäden an den Steckern zu vermeiden, 

sollte der Netzstecker möglichst höher als die Anlage 

stehen (2).

Betrieb nur mit FI-Schutzschalter, max. 30 mA.

Vor dem Hantieren im Aquarium, alle eingesetzten 

Elektrogeräte vom Netz trennen.

Beschädigtes Netzkabel nicht reparieren, sondern die 

Pumpe komplett erneuern.

Aquarienwasser-Temperatur max. +35°C (3).

Gebrauchsanleitung gut aufbewahren.

Dieses  Gerät  ist  für  Benutzer  (einschl.  Kinder)  mit 

eingeschränkten physischen, sensorischen oder 

psychischen Fähigkeiten bzw. ohne jegliche Erfahrung 

oder Vorwissen nur dann geeignet, wenn eine 

angemessene  Aufsicht  oder  ausführliche  Anleitung 

zur Benutzung des Gerätes durch eine verantwortliche 

Person sichergestellt ist. Achten Sie darauf, dass Kinder 

nicht mit dem Gerät spielen (4). 

Sécurité d’utilisation

DOC Skimmer 9460 n’est pas conçu pour une utilisation 

hors habitation (1).

Avant  toute  mise  en  service,  vérifiez  que  la  tension 

d’alimentation de la pompe corresponde bien à celle du 

réseau électrique.

Afin  d’empêcher  tout  dégât  d’eau  au  niveau  des 

raccordements électriques, les prises d’alimentation 

secteur doivent se situer plus haut que l’installation (2).

Utilisation avec disjoncteur différentiel 30mA max.

Avant toute intervention dans l’aquarium, débranchez 

l’ensemble des appareillages électriques.

N’essayez  pas  de  réparer  un  câble  de  pompe  mais 

remplacez ou renouvelez le bloc-moteur.

Température max. de l’eau véhiculée : +35°C (3).

Veuillez attentivement consulter la notice d’entretien.

Les utilisateurs (enfants inclus) ayant des limitations 

physiques, sensorielles, psychiques, ne bénéficiant pas 

d’une  expérience  ou  de  connaissances  suffisantes  ne 

peuvent utiliser cet appareil qu’avec le concours d’une 

tierce personne responsable, assurant la surveillance 

ou veillant à l’observation du mode d’emploi. Veuillez 

vous assurer que les enfants ne puissent jouer avec cet 

appareil (4). 

Safety instructions

The DOC Skimmer 9460 has not been designed for 

outdoor operation (1). 

Prior to initial operation, please check whether the 

operating voltage corresponds to the mains voltage 

available.

In order to avoid water damage in the plugs, the mains 

plug should be fitted at a higher lever than the unit (2). 

Operation is permitted only with a residual-current-

operated circuit-breaker fitted, max. 30 mA.

Before working in the aquarium, please make sure that 

all electric units used have been disconnected from the 

mains.

Do not repair a damaged mains cable - replace the pump 

completely.

Temperature of the aquarium water: m35° 

Celsius (95° F) (3).

Keep the operating instructions in a safe place.

This device is suitable for users (including children) with 

limited physical, sensorial or mental abilities or without 

any experience or previous knowledge, if suitable 

supervision or detailed instructions on the operation of 

the device is provided by a responsible person. 

Please make sure that children do not play with the 

device (4). 

Summary of Contents for DOC Skimmer 9460




























Reviews: