background image

5

Section 3. Additional Information

3.1 Battery Information

The lock requires four ‘AAA’ alkaline batteries which are housed in the internal handle. The lock has a low 

battery indicator which, when unlocking the door, will sound a continuous beep followed by a single beep.

New batteries should be installed as soon as possible after receiving any low battery indication. When the 

notification begins, the lock will only have enough power for approximately 50 times before the batteries 

are fully depleted. Expected battery life is approximately 365 days with an estimate of 3000 uses per 365 

days.

If the batteries are completely dead, you can use the included emergency backup battery pack to power 

the lock. However, it is recommended not to continue use of the backup longer than necessary; ensure 

that the batteries in the lock are replaced immediately. Please keep the emergency backup battery pack in 

an accessible area at all times. In the event of a power failure, the battery pack will be needed to unlock 

the lock.

It is highly recommended to insert the batteries only after the lock is fully installed.

Summary of Contents for YL-99




















Reviews: