➤
Exit programming mode: Press and hold the [M] button for at least 3 s
until the display stops flashing.
Changing the temperature unit
➤
Disconnect the sensor from the supply voltage.
➤
Reconnect the sensor while pressing the [V/-] and [V/+] buttons
➥
[°F] or [°C] appears on the display.
➤
Change the temperature unit using the [V/+] button.
➤
Confirm the selection using the [M] button.
➥
The programmed values for t0 and t10 will be set to 0 °C/32 °F for 0 V and
80 °C or 176 °F for 10 V after changing the temperature unit.
Changing the flow unit
➤
Disconnect the sensor from the supply voltage.
➤
Reconnect the sensor while pressing the [V/-] and [V/+] buttons
➤
Enter the access code.
➥
[GAL] or [L] appears on the display.
➤
Select the flow unit using the [V/+] button.
➤
Confirm the selection using the [M] button.
Resetting the device to the factory settings (see “Factory settings”)
➤
Disconnect the sensor from the supply voltage.
➤
Reconnect the sensor while pressing the [M] button.
➥
[rES] appears on the display.
➤
Enter the access code.
➤
To reset the device, press the [M] button.
Maintenance
Operating the device in contaminated or chalky water causes deposits that
can distort measurements.
➤
Clean the part of the sensor through which the medium flows. During
cleaning, ensure that the metallic surface of the sensor is not damaged.
Repair
The device must not be repaired by the user. The device must be decom-
missioned if it is faulty. Observe our return acceptance conditions when
returning the device to Turck.
Disposal
The devices must be disposed of correctly and must not be included
in normal household garbage.
EN
Quick-Start Guide
Operation
The device has three buttons on the front that can be used to activate func-
tions and configure settings. All values are shown in the display.
Button
Function in normal mode
Function in programming mode
V/-
Displays the current value for
the flow rate in V
Reduces the displayed value
V/+
Displays the current value for
the temperature in V
Increases the displayed value
M
Displays the currently measured
temperature or the current flow
rate for 3 s
Selects functions and
parameters
Changing the displayed value
➤
Press the [M] button as per the table below:
Press [M] Displayed function
Possible display values
1x
Current temperature
-10…+90
2x
Initial temperature value 0 V (t0) 14…162 °F/-9.9…+74.0 °C
3x
Final temperature value 10 V (t10) 46…194 °F/6.1…90.0 °C
4x
Time interval for mean value
generation (nfi)
2…16
5x
Fluid (FLU)
GLY, di, 110, 135
➥
The selected value is shown on the display for approximately 3 s.
Setting
➤
Start programming mode: Press and hold the [V/-] and [V/+] buttons at
the same time for at least 3 s until the display starts to flash.
➤
Enter the access code (factory setting: 0).
➤
Select the value to be set: Press the [M]
button as per the table below:
Press
[M] Configurable function
Possible display values
1x
Enter the access code (Cod)
0…255
2x
Initial temperature value 0 V in
°F (t0)
14…162 °F
3x
Final temperature value 10 V in
°F (t10)
46…194 °F
4x
Time interval for mean value
generation (nfi)
2…16
5x
Fluid (FLU)
GLY: glycol 0…70 %
di: deionized water
110: HT110
135: HT135
6x
Reference function ± 25 % (CAL)
7x
Configure the display: tempera-
ture only, flow rate only, flow
rate and temperature alter-
nately (diS)
°F…GAL…°FG
8x
Change the access code (COD) 0…255
Hans Turck GmbH & Co. KG | Witzlebenstraße 7, 45472 Mülheim an der Ruhr, Germany | Tel. +49 208 4952-0 | Fax +49 208 4952-264 | more@turck.com | www.turck.com
© Hans Turck GmbH & Co. KG | 100017718 2020-03 EN
FTCI-3/4D15A4P-2LUX-H1141
Technical Data
Technical data
FTCI-3/4D15A4P-2LUX-H1141
Ident-No.
6878041
Supply voltage
24 V DC ± 10% (PIN1: BN +, PIN3: BU -)
Current consumption
100 mA
Ambient temperature
32…140 °F
Output 1
Flow – analog 0…10 V (PIN 4: BK)
Output 2
Temperature – analog 0…10 V (PIN 2: WH)
Load
50…500 Ω
Medium temperature
14…194 °F
Detection range flow
Water
Water/monoethylenglycol 0…70 %
1…12 gpm
1…12 gpm
Display range
0.8…14.4 gpm
Detection range temperature
14…194 °F
Accuracy temperature
± 5 °F (68…158 °F: ± 3.0 °F) (Flow rate >
3 gpm)
Adjustment range temperature
4 mA: 14…162 °F
20 mA: 46…194 °F
t20 mA – t4 mA ≥ 32 °F
Reaction time
2…8 s
Material sensor
AISI 316 Ti / FKM
Material housing
PBT
Protection
IP 65
Compressive strength
20 bar
Factory setting code
0
Factory Settings
Unit flow
gpm
Unit temperature
°F
t0
32 °F
t10
176 °F
nFi
8
Medium
Water
Display
Flow only (gal)
