TURFCO T3000 85872 Operator'S Manual Download

Page: 3 / 20

85872 RevA

TURFCO T3000 APPLICATOR

SPECIFICATIONS

Registered Trade Mark and Patents

Patent Pending

TURFCO

is a registered trademarks of Turfco Manufacturing, Inc.

T3000™ and

VARI-RATE™ are trademarks of Turfco Manufacturing, Inc.

SPYKER, ACCUWAY, and BORDER PATROL trademarks of Spyker Spreaders, Brinly-Hardy, Inc.

DELAVAN

is a trademark of Delavan Pumps Inc. - AQUATEC™ is a trademark of AquaTec International, Inc.

BRIGGS AND STRATTON

is a registered trademark of Briggs and Stratton Corporation. Inc.

THE ENGINE EXHAUST FROM THIS PRODUCT CONTAINS CHEMICALS KNOWN TO THE STATE OF

CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER REPRODUCTIVE HARM.

WARNING

Speciﬁcations

Dimensions:

Width .......................................................... 35.5” Inches (0.90 Meter)

Height ......................................................... 50” Inches (1.27 Meter)

Length ........................................................ 65” Inches (1.65 Meter)

Weight Empty

................................................... 500 Pounds (227 Kg)

Weight Loaded

Spreader Full, Sprayer Tanks Empty .......... 620 Pounds (281 Kg)

Spreader Empty, Sprayer Tanks Full .......... 635 Pounds (288 Kg)

Spreader Full, Sprayer Tanks Full .............. 755 Pounds (342.5 Kg)

Operator Controls

Steering and Drive ..........................Forward/Reverse Speed Control, Engine Throttle, Ground

Speed Lock Pedal, Parking Brake, and Freewheel Lever

Spreader .........................................Spreader Gate Open/Close, Vari-Rate Adjuster, Spinner

Speed Wide/Narrow, Trim Spread Border Control, Accuway

Spread Pattern Adjuster, and Gate Calibration Dial.

Sprayer ............................................Full Width On/Off, Trim Width On/Off, Hand

Gun On/Off, and Spray Pressure Adjustment.

Production Rates

Spreading and/or Spraying .................4,000 Sq. Ft./Minute - 240,000 Sq. Ft./Hour

(371.6 Sq. Meters/Minute - 22,296 Sq. Meters/Hour)

Spreader Hopper Capacity

......................2.03 Cubic Feet - 120 Pounds

(0.06 Cubic Meter - 54.4 Kg.)

Minimum/Maximum Spread Width

Full Spread ..........................................18’ to 22’ Feet (5.49 to 6.7 Meter)

Trim Spread .........................................12’ to 14 Feet (3.66 to 4.27 Meter)

Sprayer Tank Capacity

.............................16 US Gallons - 135 Pounds (8 gallons per tank)

(60.57 Liter - 61.3 Kg)

Minimum/Maximum Spray Width

Full Spray ............................................9’ to 11’ Feet (2.74 to 3.35 Meter) 9’ Effective

Trim Spray ...........................................3’ to 4’ Feet (0.91 to 1.22 Meter)

Engine

........................................................Briggs and Stratton INTEK 11.5 HP (8.57 kW), with 15 amp

Electric Voltage Regulator. Optional Electric Start.

Fuel Tank Capacity

................................... 2 Gallons (7.57 liters)

Transaxle

................................................... Variable Speed with Brake and Freewheel Control

Tires

Front ................................................ 13 x 6.50-6

Rear ................................................ 18 x 6.50-8

Maximum Transport or Operating Ground Speed

.......... 5 MPH (8.04 Km/h)

Turning (Steering)

.............................................................. 9 Foot Circle (4.5 ft radius)

Maximum Slope Angle of Operation

............................... 15° Degrees

OPERATE ONLY IN AREAS WITH ADEQUATE VENTILATION. DO NOT OPERATE ENGINE IN ENCLOSED AREAS.

Summary of Contents for T3000 85872





















Search results

Summary of Contents for T3000 85872

Reviews:

Related manuals for T3000 85872

Brands by name

Popular brands

TURFCO T3000 85872, Operator'S Manual

Search results

Summary of Contents for T3000 85872

Reviews:

Related manuals for T3000 85872

Brands by name

Popular brands