CAUTION: MAXIMUM WEIGHT NOT TO EXCEED 240 LBS.
MULE
DRM-175 Mounting Instructions
550
Step 1:
Temporarily remove the tailgate. Remove the bed liner if equipped.
Step 2:
Bolt support rails to spreader mount with 1/2'' bolts. Install 1/2'' hex bolt with washer through rail
then spreader
spreader mount. Install 1/2'' locknut and tighten. Avoid over tightening to avoid potentially crushing tube.
Step 3:
Place spreader mounting rails over spreader mount support rails and install pins. Locate the spreader bracket mounting rails
on top of the bed by centering left to right and positioning the rear edged of the rails 5/8'' beyond the rear of the bed. Transferring
mounting holes to bed & drill 7/16''.
Important: Check for proper clearance underneath bed before drilling holes.
Step 4:
Bolt rails under belt with truss head bolts, fender washers, SAE washers and nylon lock nuts. Install the spreader bracket
before tightening hardware. The tailgate and bed liner may be reinstalled now.
Step 5:
Install 550 anti dump bracket with (2) 3/8'' bolts provided.
Step 6:
Install gate control cable per attached instructions.
Step 7:
Route cables at your discretion and install switch.
MULE 2500
The installation of the spreader on the 2500 is the same as the 550 with the following exceptions.
Step 1:
When positioning the mounting rails the end of the rails should be 1/2'' forward of the rear edge of the bed.
Step 2:
The universal anti dump threads into the lower weld nut on the spreader bracket assembly. Adjust rubber bumper to be 1/2''
to 3/4'' behind the rear axle - receiver hitch assembly.
CLUB CAR CARRYALL
Step 1:
Remove the bed tailgate and bottom angle trim. Also remove the 2 rear carriage bolts from the
of the bed.
Step 2:
Place spreader mounting rails over spreader mount and install pins. Locate the 2 front outside mounting rails over the holes
from the carriage bolts remove in step 1.
Step 3:
Install truss head bolts, fender washers, SAE washers and nylon lock nuts in the carriage bolt holes. Transfer the remaining
mounting rail holes and bolt rails into bed.
JOHN DEERE GATOR
Step 1:
Remove the bed tailgate.
Step 2:
Place spreader mounting rails over spreader mount and install pins.
Step 3:
Locate the spreader bracket mounting rails on top of the bed by centering left to right, push main mount
up against rear
of bed to locate mounting rails. Transfer mounting holes to bed.
Step 4:
Install mounting rails with truss head bolts, fender washers, SAE Washers and nylon lock nuts in the 1/2'' mounting holes.
Step 5:
The universal anti dump threads into the lower weld nut on the spreader bracket assembly. The rubber bumper should be
adjusted to rest against the frame of the vehicle. The trailer hitch bracket may need to be relocated depending on
ation.
© Trynex International 2009 L1302
1 — 45
R
Summary of Contents for TS-1200-E
