background image

 [4] 

1.

GETTING STARTED

This manual is written as a

 

guide for you to install, connect, and test the OBSG-

HG-CV optical speedgates.  You will learn how they work, how to operate them, which 
components are which, and what to  look  for  during  occasional  maintenance  and  repair 
visits.  We  ask  that  you  read  the entire manual before beginning the installation process.   

2.

OPERATIONAL OVERVIEW

The    OBSG-HG-CV  is  an  optical  speedgate  with  center  barriers  configured

 

for

continuous  bi-directional  cardholder  traffic  flow.    The    OBSG-HG-CV  standard 
configuration  is  set  at  card  in  /  card  out  for  secure  bi-directional  traffic  flow.    The  
OBSG-HG-CV can also be set to operate in several other modes that are set by the Remote 
Lane Controller, or through your access control system.   These modes include Free Exit, 
Free Entry, Exit Only, Enter Only, Disable Lane, and Close Lane. 

3.

MOUNTING AND INSTALLATION

Installing  speedgates  is  a  simple  process,  but  each  stage  requires  extra  care  to insure 
a smooth and problem free installation.  Here are a few pointers to keep in mind during 
installation: 

1. Beam alignment is critical.  The physical layout and securing of the speedgate

to the floor in the installation phase, should be carefully planned and laid out. The

floor must be level to allow for a secure mounting of the pedestal.  Extra care at
this  early  stage  will  ensure  a  smooth  and  problem  free  installation.    Improper
layout will affect beam alignment and cause the lanes to malfunction. Be sure the

pedestals are square and parallel in relationship to each other.  Always ensure the
proper lane width, and measure diagonally to be sure the pedestals are square.

2. Use gloves, if necessary.  In some cases the outer material of the cabinets can

be  very  sensitive  to  oils  (Unfinished  Brass  or  Muntz  Metal),  and  may  cause  a

permanent mark that will require replacement of the side/top panels.

3. Never place tools or metal objects on top of the turnstile.  Please be sure

not  to  leave  items  that  may  scratch  the  cabinet  leaning  against  the  side  of  the
pedestal.

www.TURNSTILES.us / www.entrapass.com / 8641 S. Warhawk Road, Conifer, CO 80433 / 303-670-1099

Summary of Contents for OBSG-HG

















Reviews:

Related manuals for OBSG-HG