background image

 [7] 

Transmitter Sensors 

SIO – Secondary 

Interconnect Board 

Chopper Board & 

Resistor  

Motor & Gearbox 

PIO- This is the “workhorse” of the speedgate. The Primary I/O Board is located inside 

every pedestal, except the last pedestal in the suite. There is one PIO per lane. This board 
receives incoming power, all access control input signals, and inputs from the Remote 
Lane Controller. This board outputs serial communications to the SIO, alarm conditions 

via relays, and produces sound. The PIO contains the master program for how the lane 
will function, as well as saves all of the settings for each lane. 

Chopper Board & Resistor –

 

This board is in line with the direct motor power. It is 

used to direct any generated power from the movement of the arms into the resistor to 

prevent damaging any components on the PIO.  

Motor & Gearbox – Each lane has a primary and secondary motor. The primary motor 

is directly connected to the secondary motor, to the chopper assembly, and to the mini-
master. 

B: Secondary Side Electronics

Transmitter Sensors- There are 17 transmitter sensors that provide a signal for the 
receiver beams in the OBSG-HG-CV. The transmitter sensors will always be found on the 

secondary side of the lane. 

 

www.TURNSTILES.us / www.entrapass.com / 8641 S. Warhawk Road, Conifer, CO 80433 / 303-670-1099

Summary of Contents for OBSG-HG

















Reviews: