background image

OPERATING INSTRUCTIONS 

  

11/26/2019 

 

 

 

 

2

 

 

 

 

  

Description 

 
The Max HT provides a compact, efficient heater for heating air or inert gases to 1652°F (900°C).  The Max HT 
comes in various power ratings ranging from 18kW to 36kW. The heater is equipped with two (2) t

ype “K” 

thermocouples.  One thermocouple measures the inlet air temperature (S1) and the other is a dual probe type 
“K” thermocouple with each probe of the exit thermocouple used to measure exit air temperature.  One is 
typically used for process temperature control and the other to monitor high temperature limit. When powered 
and controlled with TUTCO SureHeat approved controls (sold separately) you are provided a convenient, cost 
effective solution for safely controlling the AC power to your Max HT.  If operated correctly, the heater will 
operate continuously for 5000 hours or longer.   
 
 
 

 
 

Limited Warranty 

 

 
 

TUTCO SureHeat warrants that all products to be delivered hereunder will be free from defects in material and 
workmanship at the time of delivery.  TUTCO SureHeat's obligation under this warranty shall be limited to (at its 
option)  repairing,  replacing,  or  granting  a  credit  at  the  prices  invoiced  at  the  time  of  shipment  for  any  of  said 
products.  This warranty shall not apply to any such products which shall have been repaired or altered, except 
by TUTCO SureHeat, or which shall have been subjected.  TUTCO SureHeat shall be liable under this warranty 
only  if  (A)  TUTCO  SureHeat  receives  notice  of  the  alleged  defect  within  sixty  (60)  days  after  the  date  of 
shipment; (B) the adjustment procedure hereinafter provided is followed, and (C) such products are, to  TUTCO 
SureHeat

’s satisfaction, determined to be defective. 

 
THE  WARRANTY  SET  FORTH  IN  THE  PRECEDING  PARAGRAPH  IS  EXCLUSIVE  AND  IN  LIEU  OF  ALL 
OTHER  WARRANTIES,  EXPRESS  OR  IMPLIED,  INCLUDING,  WITHOUT  LIMITATION,  ANY  IMPLIED 
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE OR OF MERCHANTABILITY. 
 
The  information  contained  in  this  manual  is  based  on  data  considered  to  be  true  and  accurate.    Reasonable 
precautions for accuracy has been taken in the preparation of this manual, however TUTCO SureHeat assumes 
no responsibility for any omissions or errors, nor assumes any liability for damages that may result from the use 
of the product in accordance with the information contained in this manual. 

 

Please  direct  all  warranty/repair  requests  or  inquiries  to  the  place  of  purchase,  and  provide  the  following 
information, in writing: 
 
(A) 

Order number under which products were shipped 

(B) 

Model/Serial Number of product 

(C) 

Reason for rejection 

 
PRODUCTS CAN NOT BE RETURNED TO TUTCO SUREHEAT WITHOUT AUTHORIZATION. 
Replacement,  repair,  or  credit  for  products  found  to  be  defective  will  be  made  by  the  place  of  purchase.    All 
products  found  to  be  not  defective  will  be  returned  to  the  Buyer;  transportation  charges  collect  or  stored  at 
Buyers expense. 
 

 

 

 
 

Summary of Contents for Max HT













Reviews: