background image

 

TP9KAC-TUX 

Mar 2019 

IMPORTANT NOTES 

READ THE INSTALLATION AND OPERATION MANUAL IN ITS ENTIRETY BEFORE 

ATTEMPTING TO INSTALL THE LIFT. 

·

  Do not install this lift on any surface other than concrete, conforming to minimum specifications. 

·

  Do not install this lift over expansion joints or cracks. Check with building architect. 

·

  Do not install this lift on a second floor with a basement beneath without written authorization from 

building architect. 

·

  Do not install this lift outdoors unless special consideration has been made to protect the power unit 

from inclement weather conditions. 

·

  A level floor is recommended for proper installation and operation. Concrete should be a minimum 

of 4-1/4

” thickness and 3,000 psi tensile strength with steal or fiber mesh reinforcement. 

·

  The  lift  is  intended  to  raise  the  entire  body  of  the  vehicle.  Do  not  attempt  to  lift  only  part  of  the 

vehicle. Improper use of this equipment could result in damage to the lift, yourself or other property. 

·

  The lift is intended to lift vehicles only. It is not designed to lift any person or equipment containing 

persons. 

·

  Users of this equipment should be qualified, responsible and should follow the operation and safety 

guidelines set forth in this manual. 

·

  For specifications on concrete pads, please call for technical assistance. 

·

  Improper  installation  can  cause damage or  injury.  The  Manufacturer  will  NOT  assume  liability  for 

loss or damage of any kind, expressed or implied, resulting from improper installation or use of this 

product.   

 

DEFINITION 

Surface Mounted, Two-Post, Clear-Floor Lift w/ Overhead Beam, Hydraulic 

‘chain-over’ Drive, 

9,000 lbs. Capacity. 

The name / model numbers are designated below: 

 

·

 

Model number TP9KAC-TUX - Asymmetric Swing Arm configuration   

 

BASIC SPECIFICATIONS 

Model 

Description 

(Clear Floor) 

Capacity 

Lifting Time 

Overall 

Height 

Overall 

Width 

Lifting 
Height 

Between 

Columns 

TP9KAC-TUX 

Asymmetric 

9,000 lbs. 

50 Sec 

142-11/16

” 

141

” 

72

” 

110-7/16

” 

 

Summary of Contents for TP9KAC-TUX

























Reviews: