background image

 

TYWRD2S Datasheet 

Hangzhou Tuya Information Technology Co., Ltd.  18 

V2.0.0   

8 Appendix: Statement 

Federal Communications Commission (FCC) Declaration of Conformity 

FCC Caution: Any changes or modifications not expressly approved by the party 

responsible for compliance could void the user's authority to operate this equipment. 

This device complies with Part 15 of the FCC Rules. 

Operation is subject to the following two conditions: (1) This device may not cause harmful 

interference, and (2) this device must accept any interference received, including 

interference that may cause undesired operation. 

This device and its antenna(s) must not be co-located or operating in conjunction with any 

other antenna or transmitter. 

15.105 Information to the user. 

(b) For a Class B digital device or peripheral, the instructions furnished the user shall 

include the following or similar statement, placed in a prominent location in the text of the 

manual: 

Note: This equipment has been tested and found to comply with the limits for a Class B 

digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against harmful interference in 

a residential installation. This equipment generates, uses and can radiate radio frequency 

energy and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications. However, there is no guarantee that 

interference will not occur in a particular installation. If this equipment does cause harmful 

interference to radio or television reception, which can be determined by turning the 

equipment off and on, the user is encouraged to try to correct the interference by one or 

more of the following measures: 

—Reorient or relocate the receiving antenna. 

—Increase the separation between the equipment and receiver. 

—Connect the equipment into an outlet on a circuit different from that to which the 

receiver is connected. 

—Consult the dealer or an experienced radio/TV technician for help. 

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled 

environment. This equipment should be installed and operated with minimum distance 20 

cm between the radiator and your body. 

Summary of Contents for TYWRD2S




















Reviews: