Multiformat 3D Monitor 27
PAGE I >> PAGE II
USER CONFIG SET
LOCK NUMBER
LOCK ENABLE
OSD DISPLAY
OSD POSITION
INTERNAL PATTERN
SET DEFAULT
PAGE II >> PAGE I
KEY LED
KEY FUNCTION 1
KEY FUNCTION 2
KEY FUNCTION 3
KEY FUNCTION 4
KEY LOCK
USER 1
12345678
--------
CONTINUE
CENTER
OFF
ON
ASPECT
H/V DELAY
FREEZE
TIMECODE
DISABLE
TDM-243W
TDM-243W
• USER CONFIG SET
- This item saves and applies three kinds of user
configurations.
- Available modes are USER1, USER2 and USER3.
- Effective items for each USER1, USER2 and
USER3 settings are [MARKER] menu of MARKER,
CENTER MARKER, SAFETY AREA, MARKER
MAT and MARKER COLOR and [PICTURE]
menu of , BRIGHT, CONTRAST, CHROMA,
PHASE, APERTURE and NOISE REDUCTION.
• LOCK NUMBER
- This item is not available.
• LOCK ENABLE
- Factory use only.
• OSD DISPLAY
- Controls the OSD display time.
- Available values are 20 SEC, 6 SEC and
CONTINUE.
• OSD POSITION
- Controls the OSD position.
- Available positions are CENTER, Top-
Right(R-T), Bottom-Right(R-B), Bottom-Left(L-B)
and Top-Left(L-T).
• INTERNAL PATTERN
- This item generates internal white pattern.
- The white level select between 0% and 100%
(Per 5% increase or decrease).
• SET DEFAULT
- User can use SET DEFAULT menu to initialize
to factory setting.
- Set default items are BRIGHT, CONTRAST,
CHROMA, PHASE and APERTURE and set 0.
• KEY LED
- This item controls key LED On/Off.
- If the button with LED is pressed with the
KEY LED Off, LED comes on but goes off after
5 seconds later.
• KEY FUNCTION 1
- User can select the function for [F1] button.
- Selectable Items : ASPECT, H/V DELAY,
FREEZE, WAVEFORM, TIMECODE, CC SEL, ALM
SEL., OUTPUT MODE, FAST MODE, FILTER,
FORCE Psf, UMD, COLOR TEMP, BLUE ONLY
3D-L/R SWAP, 3D DISPARITY and 3D-FORMAT.
• KEY FUNCTION 2
- User can select the function for [F2] button.
- Selectable Items : ASPECT, H/V DELAY,
FREEZE, WAVEFORM, TIMECODE, CC SEL, ALM
SEL., OUTPUT MODE, FAST MODE, FILTER,
FORCE Psf, UMD, COLOR TEMP and BLUE ONLY.
• KEY FUNCTION 3
- User can select the function for [F3] button.
- Selectable Items : ASPECT, H/V DELAY,
FREEZE, WAVEFORM, TIMECODE, CC SEL, ALM
SEL., OUTPUT MODE, FAST MODE, FILTER,
FORCE Psf, UMD, COLOR TEMP and BLUE ONLY.
• KEY FUNCTION 4
- User can select the function for [F4] button.
- Selectable Items : ASPECT, H/V DELAY,
FREEZE, WAVEFORM, TIMECODE, CC SEL, ALM
SEL., OUTPUT MODE, FAST MODE, FILTER,
FORCE Psf, UMD, COLOR TEMP and BLUE ONLY.
• KEY LOCK
- This item locks all buttons except power,
input select, and menu buttons.
[9] SYSTEM
5. Menu Operations
Summary of Contents for TDM-243W
