Twiins D1, Instruction Manual

8

Welcome

Congratulations and thank you for purchasing a 

Twiins

®

 D1 device. This Bluetooth

®

 system has been 

specifically designed to receive calls safely and easily 

while travelling on your scooter or motorcycle.

The Twiins

®

 D1 system is compatible with all 

Bluetooth

®

 devices that transmit audio (mobile 

phones, smartphones, GPS navigators and other 

devices) using the profiles specified in the manual.

This device is designed so that it may be wholly 

integrated into your helmet. It can be operated and 

paired easely through a single control button (1b).

A single red/blue LED indicator (1a) serves to display 

connection status, pairing, battery charging and low 

battery. The Twiins

®

 D1 device weighs only 35 g.

For better use of the Twiins

®

 D1 device, please read 

this manual and keep it in a safe place or find it at   

www.twiins.com

Charging the Twiins

®

 D1

Before using your Twiins

®

 D1 device for the first time, 

you must charge the device completely.

Connect the terminal (3) to the provided USB cable (5) 

and then connect the cable to a USB charging port.

While charging, the red LED light will switch on (1a) and 

it will switch off once charging has been completed.

NOTE

: Don’t pull on the cable to disconnect it from the 

USB port

NOTE

: As time goes by, batteries gradually lose their 

charge. This is why it’s important to charge the battery 

fully before using the device and allow the battery to 

use almost all of it’s charge in between charging cycles. 

WARNING:

 If you plan to store your Twiins

®

 device 

for a long period of time, be sure to recharge it at 

least once every six months to ensure perfect battery 

function.

Installation

The Twiins

®

 D1 is very easy to install into a helmet. 

Remove the side padding from the inside of the helmet 

(if it can be removed) and place the device (2) at the 

height of your ear. The device is designed to be placed 

on the left side, as shown in figure 1. In order to affix the 

speaker, a Velcro pad is provided (male and female) with 

an adhesive backing (7). In case you need to use the 

Velcro, stick the male part of the pad onto the device 

and the female part onto the inside of the helmet.

Depending on the internal configuration of each type of 

helmet, it may be necessary to use the entire Velcro pad 

or only a part of it (see figure 2). In some cases, it may 

only be necessary to stick the male part onto the device 

as the inside of the helmet may have padding that can 

serve as Velcro (female).

If needed, comfort pads (6) to place on the headphones 

are also provided, in order to improve comfort against 

your skin.

The charging cable (3) must be placed on the lateral-

back section of the helmet so as to facilitate access to 

charge the device.

Place the microphone (1) on the front section of the 

helmet (close to and oriented towards your mouth, 

always protecting the microphone with the padding).

Linking/Pairing

To use the Twiins

®

 D1, it’s necessary to pair it to the 

Bluetooth

®

 device you wish to connect it to (mobile 

phone, GPS navigator). While the device is switched 

off, hold the control button (1b) until the LED indicator 

(1a) begins flashing in Red and Blue. The mobile phone 

or GPS navigator will find the device under the name 

T-LSA. Select the T-LSA device and, if necessary, enter 

the access code: 0000.

NOTE

: Pairing is a process that only needs to be 

completed once. When the Twiins

®

 D1 is paired to a 

specific device, both devices will connect automatically 

when switched off and on.

Switching on/off 

Switching on

: press and hold the button (1b) for a few 

seconds until the speaker provides an acoustic signal 

and the LED indicator (1a) begins to flash in Blue.

Switching off

: press and hold the control button (1b) for 

a few secondspress and hold the control button (1b) for 

TWIINS

®

 D1

INSTRUCTION MANUAL