Twiins D2, Instruction Manual

7

TWIINS

®

 D2

INSTRUCTION MANUAL

Welcome

Congratulations and thank you for purchasing a Twiins

®

D2 device. This Bluetooth

®

 device has been especially 

designed to keep you connected to your phone and 

listen to your favourite music while travelling on your 

scooter or motorcycle.

The Twiins

®

 D2 system is compatible with all Bluetooth

®

devices that transmit audio (mobile phones, smart-

phones, GPS navigators and other devices) using the 

profiles specified in the manual.

This device is designed so that it may be wholly inte-

grated into your helmet. It can be operated and paired 

easily through a single control button (1b).

A single red/blue LED indicator (1a) serves to display 

connection status, pairing, battery charging and low 

battery. The Twiins

®

 D2 device weighs only 55 g.

For better use of the Twiins

®

 D2 device, please read this 

manual and keep it in a safe place or find it at

www.twiins.com

Charging the Twiins

®

 D2

Before using your Twiins

®

 D2 device for the first time, 

you must charge the device completely.

Connect the terminal (3) to the provided USB cable (5) 

and then connect the cable to a USB charging port.

While charging, the red LED light will switch on (1a) and 

it will switch off once charging has been completed.

NOTE

: Don’t pull on the cable to disconnect it from the 

USB port.

NOTE

: As time goes by, batteries gradually lose their 

charge. This is why it’s important to charge the battery 

fully before using the device and allow the battery to 

use almost all of it’s charge in between charging cycles.

WARNING:

 If you plan to store your Twiins

®

 device 

for a long period of time, be sure to recharge it at least 

once every six months to ensure perfect battery func-

tion.

Installation

The Twiins

®

 D2 is very easy to install into a helmet. Re-

move the side padding from the inside of the helmet (if it 

can be removed) and place the devices (2) and (4) at the 

height of your ears. The device is designed so that the 

main unit with the boom microphone is placed on the 

right side. The wire between devices (2) and (4) must be 

stored inside the helmet, under the padding. In order 

to affix the headphones, two Velcro pads are provided 

(male and female) with an adhesive backing (7). In case 

you need to use the Velcro, stick the male part of the 

pad onto the device and the female part onto the inside 

of the helmet.

Depending on the internal configuration of each type of 

helmet, it may be necessary to use the entire Velcro pad 

or only a part of it (see figure 2). In some cases, it may 

only be necessary to stick the male part onto the device 

as the inside of the helmet may have padding that can 

serve as Velcro (female).

If needed, comfort pads (6) to place on the headphones 

are also provided, in order to improve comfort against 

your skin.

The charging cable (3) must be placed on the lateral-

back section of the helmet so as to facilitate access to 

charge the device.

Place the microphone (1) on the front section of the hel-

met (close to and oriented towards your mouth, always 

protecting the microphone with the padding).

Linking/Pairing

To use the Twiins

®

 D2, it’s necessary to pair it to the 

Bluetooth

®

 device you wish to connect it to (mobile 

phone, GPS navigator). While the device is switched 

off, hold the control button (1b) until the LED indicator 

(1a) begins flashing in Red and Blue. The mobile phone 

or GPS navigator will find the device under the name 

T-LSA. Select the T-LSA device and, if necessary, enter 

the access code: 0000.

NOTE

: Pairing is a process that only needs to be com-

pleted once. When the Twiins

®

 D2 is paired to a specific 

device, both devices will connect automatically when 

switched off and on.

Switching on/off

Switching on:

 press and hold the button (1b) for a few 

seconds until the speaker provides an acoustic signal