twin city BAE Installation, Operation & Maintenance Manual Download

Page: 5 / 68

Twin City Engineering Supplement ES-52

Operation Check List

Verify.that.proper.safety.precautions.have.been.followed:

□

. Electrical.power.must.be.locked.off.

Check.fan.mechanism.components:

□

System.connections.are.properly.made.and.tightened..

□

Bearings.are.properly.lubricated.

□

Wheel,.drives.and.fan.surfaces.are.clean.and.free.of.

debris.

□

Rotate.the.impeller.by.hand.to.verify.it.has.not.shifted....

..in.transit.

□

Check.fan/wheel.overlap..(See.Figure.7.)

□

Drives.on.correct.shafts.(not.reversed).

□

Check.position.of.guards.to.prevent.rubbing.

Check.fan.electrical.components:

□

Motor.is.wired.for.proper.supply.voltage.

□

Motor. was. properly. sized. for. power. and. rotational.

inertia.of.rotating.assembly.

□

Motor.is.properly.grounded.

□

All.leads.are.properly.insulated.

Trial.“bump”:

□

Turn. on. power. just. long. enough. to. start. assembly.

rotating.

□

Check. rotation. for. agreement. with. rotation. arrow.

Does. the. assembly. make. any. unusual. noise?..

(See.Figure.8.)

□

Check. drive. alignment. and. tension.. Does. this. meet.

with.drive.manufacturer’s.recommendations?

□

Correct. any. problems. which. may. have. been. found....

(Follow. safety. guidelines. -. shut. power. off.). Perform...

checklist.again.until.unit.is.operating.properly.

□

Run.unit.up.to.speed.

Verify.fastener.tightness..These.may.have.loosened.dur-

ing.shipment.or.installation.

□

Setscrews.attaching.wheel.hub.to.shaft.

□

Setscrews.in.drive.sheaves.or.coupling.

□

Nuts.on.inlet.funnel.

□

Nuts.and.bolts.holding.motor.

□

Nuts. holding. housing. frame. to. base. and. base. to.

ground.

□

Nuts. on. accessories. including. shaft. seal,. access.

doors.and.pie-splits.

□

Bolts.in.taper-lock.bushings.

□

Grease.line.connections.

□

After.one.week.of.operation,.check.all.nuts,.bolts.and.

setscrews.and.tighten.if.necessary.

Maintenance of Fans

This. section. contains. general. maintenance. instructions.

for.your.Twin.City.Fan.&.Blower.unit..For.specific.infor-

mation. about. maintenance. of. components,. particularly.

for.special.application.fans,.see.the.attached.documents.

General Motor Maintenance

The.three.basic.rules.of.motor.maintenance.are.keep.the.

motor.clean,.dry.and.properly.lubricated.

. Keeping. motors. and. windings. clean. is. important.

because.dirt.and.dust.serve.as.thermal.insulators..Heat.

normally. dissipated. by. the. motor. is. trapped. causing.

overheating.and/or.premature.failure..Blow.dust.and.dirt.

out.of.windings.and.off.the.motor.periodically..Use.low.

pressure.(50.psig).airstream.so.that.winding.damage.does.

not. occur.. Keep. the. area. surrounding. the. motor. open.

so. the. air. can. circulate. through. the. motor. cooling. fan..

Follow.normal.maintenance.schedule.given.to.the.right.

. Motors. should. be. kept. dry. to. avoid. electrical. short.

circuits..Motors.kept.in.storage.for.long.periods.of.time.

can.have.moisture.condense.on.the.windings..Be.certain.

the.motor.is.dry.before.using.

. Some. smaller. motors. are. lubricated. for. life.. Motor.

bearing. lubrication,. if. required,. must. follow. a. rigorous.

schedule.. Motors. less. than. 10. hp. running. about. eight.

hours. a. day. in. a. clean. environment. should. be. lubri-

cated.once.every.five.years;.motors.15.to.50.hp,.every.

3.years;.and.motors.50.to.150.hp,.yearly..For.motors.

in.a.dusty.or.dirty.environment.or.running.24.hours.a.

day,.divide.the.service.interval.by.2..If.the.environment.

is.very.dirty.or.high.temperatures.exist,.divide.the.ser-

vice.interval.by.4..Lubrication.requirements.are.normally.

attached.to.the.motor..Do.not.overlubricate.

. Motors.controlled.by.variable.frequency.drives.(VFDs).

should.be.wired.in.accordance.with.VFD.manufacturer's.

instructions..The.motor.must.be.grounded.to.earth.and.

proper.shielded.cabling.must.be.used..Grounding.rings.

should.be.considered.

Drive Maintenance

V-belt. drives. need. periodic. inspection. and. occasional.

belt. replacement.. When. inspecting. drives,. look. for. dirt.

buildup,.burrs.or.obstructions.which.can.cause.prema-

ture. belt. or. drive. replacement.. If. burrs. are. found,. use.

fine. emery. cloth. or. a. stone. to. remove. the. burr.. Be.

careful.that.dust.does.not.enter.the.bearings.

. Check. the. sheaves. for. wear.. Excessive. slippage. of.

belts.on.sheaves.can.cause.wear.and.vibration..Replace.

worn.sheaves.with.new.ones..Carefully.align.sheaves.to.

avoid.premature.sheave.failure.

. Observe. belts. for. wear.. If. fraying. or. other. wear. is.

observed. to. be. mostly. on. one. side. of. the. belts,. the.

drives.may.be.misaligned..Reinstall.the.drives.according.

to.instructions.given.for.Fan.Installation.–.Disassembled.

Units..Never.use.belt.dressing.on.any.belts.

. When. replacing. belts,. replace. the. entire. set.. After.

initial. replacement. and. tensioning,. recheck. belt. tension.

after.a.few.days.to.adjust.belt.tension.again..(New.belts.

require.a.break-in.period.of.operation.)

Bearing Maintenance

For. instructions. covering. special. lubrication. intervals,.

bearing.assembly.or.disassembly,.or.installation.details,.

see. attached. documents.. Any. bearing. which. is. disas-

sembled. should. be. kept. separate. from. other. bearing.

parts. as. components. may. not. be. interchangeable..

Maintain. cleanliness. of. components. and. bearings. to.

prevent.bearing.contamination.

BAF, BAE, EPF, EPQ,
APF & APQ Wheels

HIB, BCS

& BCN
Wheels

BC, RBA &

TBA Wheels

HRT & RTF

Wheels

FC & NFC

Wheels

RBO, RBW, RBR
MBO, MBR &
TBR Wheels

tati

Figure 8. Proper Wheel Rotation

Summary of Contents for BAE





































































Search results

Summary of Contents for BAE

Reviews:

Related manuals for BAE

Brands by name

Popular brands

twin city BAE, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for BAE

Reviews:

Related manuals for BAE

Brands by name

Popular brands