background image

12 

 

GRATES 

Round Grates 

 

The easiest way to clean the grates is to scrub them with a barbeque 
brush immediately after cooking is completed and the flame is turned 
off.  

 

Wear a barbeque mitt to protect your hands from the heat and steam.  
Dip a brass bristle barbeque brush in tap water and scrub the hot 
grates. Dip the brush frequently in tap water. Steam, created as water 
comes in contact with the hot Power Burner, helps loosen food 
particles stuck in the Power Burner. These food particles will either 
get burned or fall into the cleaning pan.  Cleaning of the Power Burner 
would be longer and more difficult if the Power Burner grates are 
allowed to cool before cleaning.  

 
Heavy Duty Grate  
Use warm water and soap to clean the heavy duty grates. Use non-abrasive 
sponge to clean off the food particles. 
 
 
 

BURNERS 

Burners are made of heavy gauge brass and can be cleaned using a bristle 
brush, warm water and soap. Check every port hole for clogs. Use a wire pin 
to clean out clogged ports. Make sure the burner is dry before installing it 
back to the Power Burner

 
 

DRIP PAN 

The drip pan collects grease, liquid and fallen food particles. Allow the pan 

and its contents to cool before cleaning. Slide the pan out and wipe it clean. 

Make sure the drip pan is fully inserted back into the Power Burner. It is 

highly recommended to clean the pan after every use to avoid any possibility 

of a grease fire.  DO NOT use the Power Burner without the drip pan pushed 

all the way to the back of the Power Burner unit. 

 

SPIDER AND INSECT WARNING 

Spiders and other insects can nest in the burners and orifices of this and any other outdoor products, which 
causes the gas to flow from the front of the burner.  This can create a dangerous condition that can cause a fire 
behind the valve panel, damaging the Power Burner and making it unsafe to operate. 
Inspect the burners once a year, or if the Power Burner has not been used for more than a month or if any of the 
following conditions occur: 

1.

 

The smell of gas in conjunction with the burner flames appearing yellow. 

2.

 

The burner does not reach temperature. 

3.

 

The burner heats unevenly. 

4.

 

The burner makes popping noise. 

 

 

 

 

Summary of Contents for TEPB24HG-C

























Reviews: