TWM Zero Fighter 60S Instruction Manual Download

Page: 10 / 16

A064SPO29991407

P.9

Plywood

3x44x121mm

Included with the
Radio Set.

Fix the throttle servo tray either to
the right or left side of the fuselage
according to your throttle pushrod
location.

Plywood

6x60x119mm

Bottom View

Balsa 7x7x40mm

Receiver / Battery

Sponge Sheet 10 x 80 x 200mm

Bottom View

Battery

Fuel Tank
380cc

Receiver

Throttle

Servo

Rudder

Servo

Elevator

Servo

Radio Equipment

Straper

Fuel Tube

Front

Install Sponge for inserting Battery and Receiver.

Straper

1mm

Charge Receptacles
KP0041300

Elevator Servo

Pushrod Connector

KM2x8mm

M2 Nut

Elevator Pushrod

Ø1.8x80mm

J1(Pushrod Ø1.8x80mm)

J2(Pushrod Ø1.8x655mm)

Servo Set

3x3mm

Set Screw

Nut

Linkage

Connector

2mm

Washer

Throttle Pushwire

Please refer to the attached sheet for linkage connector installation.

3x 3mm Set Screw

2mm
Washer

M2 Nut

Throttle Servo

1.5mm

Summary of Contents for Zero Fighter 60S

















Search results

Summary of Contents for Zero Fighter 60S

Reviews:

Related manuals for Zero Fighter 60S

Brands by name

Popular brands

TWM Zero Fighter 60S, Instruction Manual

Search results

Summary of Contents for Zero Fighter 60S

Reviews:

Related manuals for Zero Fighter 60S

Brands by name

Popular brands