background image

  

 

UPS-ST2424-UBNT 

UPSPro™ Backup 

Power System 

▫ 

Wireless Base Stations 
and Client Devices 

▫ 

Surveillance Cameras 

▫ 

Remote Sensors 

▫ 

UBNT Equipment 

▫ 

Microtik Equipment 

Congratulations! 

on your purchase of the UPSPro™ outdoor 

backup power system. Please take a moment to review this Qwik 
Install Guide before assembly or battery installation. 

DANGER! Avoid Powerlines!  

You Can Be Killed! 

When following the instructions in this guide take extreme care to avoid 
contact with overhead power lines, lights and power circuits. Contact 
with power lines, lights or power circuits may be fatal. We recommend 
to install no closer than 20 feet to any power lines. 

Safety: 

For your own protection, follow these safety rules. 

▫ 

Perform as many functions as possible on the ground 

▫ 

Do not attempt to install on a rainy, windy or snowy day or if 
there is ice or snow accumulation at the install site or if the 
site is wet. 

▫ 

Make sure there are no people, pets, etc. below when you are 
working on a roof or ladder.

 

Recommended Tools: 

Phillips Screwdriver, 13mm and 10mm 

Open End Wrench, 8mm nut driver, Flat Blade Screwdriver 

Please help preserve the environment and return 
used batteries to an authorized depot 

Summary of Contents for UPSPro









Reviews: