background image

 

12V, 18V, 24V or 48V depending on which model is purchased. There 

is also an auxiliary protected output on the back of the controller to sup-

ply 12VDC. This is useful for applications requiring 2 different voltages. 

11.

 

POE SWITCH: 

Tycon Power offers a universal voltage 5port and 

8port POE switch if more than one device needs to be powered from 

the battery system. The 

TP-SW5-NC 

and 

TP-SW8-NC

 offer the unique 

feature that the voltage supplied to the switch is  the POE voltage sent 

to the devices. So 12VDC in and you get 12VDC POE to the devices. 

The operating voltage is 12V to 56VDC.

 

 

 

Limited Warranty 

The UPSPro

® 

products are supplied with a limited 24 month warranty 

which covers material and workmanship defects. This warranty does 

not cover the following:  

▫ 

Parts requiring replacement due to improper installation, misuse, poor site 
conditions, faulty power, etc. 

▫ 

Lightning or weather damage. 

▫ 

Physical damage to the external & internal parts. 

▫ 

Products that have been opened, altered, or defaced. 

▫ 

Water damage for units that were not mounted according to user manual. 

▫ 

Usage other than in accordance with instructions and the normal intended 

use. 

 

NOTES 

Summary of Contents for UPSPro UPS-PL









Reviews: