background image

 

TECH CORNER

 

 

 

1.

CONTROLLER: 

The  controller  turns  off  power  to  the  load  at  11V 

(22V  if  24V  array)  and  reconnects  when  the  battery  reaches  12.6V 

(25.2V if 24V array). This protects battery from over-discharge and in-

creases battery life and performance. 

2. 

CAPACITY: 

With  a  typical  AP  running  4W  average.  A  single  12V 

52Ah battery should be able to provide backup power for up to 75 hours 

at room temperature. For cold temperatures the capacity is reduced by 

20-30%. 

3. 

VENTING: 

The  enclosure  is  vented  thru  the  included  PowerVent™. 

The fan is thermostatically controlled to  turn  on  when the temperature 

inside the enclosure exceeds 45C. It runs on 12V to 24VDC. 

4.

 DUAL INPUTS: 

The UPS-ST-600 can be used with AC Power alone 

or Solar Power alone or a combination of both. 

5. 

SOLAR PANEL: 

The MPPT controller used in the UPS-ST-600 can 

handle  a  maximum  panel  size  of  550W  @  12V  Battery  or  1100W  @ 

24V  Battery.  Maximum  panel  voltage  is  90V.  Do  not  exceed  40A  into 

the solar panel input of the solar controller.  

Summary of Contents for UPSPro UPS-ST-600









Reviews: