Tymetal Corp. TYM 1000 Installation Manual Download

Page: 16 / 38

TYM 1000/2000 Slide Gate Operator Installation Guide

- 14 -

Rev 9 02/14

Advanced Controller

Programming

Entering Advanced Programming Mode

To access and program the Advanced Programming

functions, for each programming session, Advanced

Programming must be enabled.
After exiting programming, the Advanced Programming

functions will be available on the programming display during

the next programming session unless the operator has run

50 or more cycles. After that, Advanced Programming must

be enabled again.

Maximum Run Time

The factory default for the Maximum Run Time (MRT) is

99 seconds. When the operator starts, a timer will begin

counting. If an open or close limit is not reached or an

obstacle or reversing input is not received before the timer

expires, the operator will stop, the unit locks out and the

alarm sounds. The timer can be set for 10 to 99 seconds.

See p. 27 for reset

Single Button Input Setup

This function is used for selecting the operation for single

button controls and radio receivers.
The factory default sets the SINGLE input terminal so

successive inputs will cycle the operator in OPEN-STOP-

CLOSE-STOP order.
Alternately, the SINGLE input can be set to cause the gate

to OPEN unless the gate is fully open. If the gate is fully

open, the input will cause the gate to CLOSE.

Stagger Mode

(Rarely used in slide gate installations)

This function is used in dual gate installations only. The

factory default sets the Stagger Mode to OFF. In dual gate

installations the two operators communicate through the

3-wire COMM LINK interface. When using the Stagger

Mode, set one operator for delayed opening and the other

operator for delayed closing. The Stagger Delay Time

programming function (see below) sets the length of the

delay.

NOTE: This function will only be displayed if dual gate

operation is selected.

FUNCTION

ADVANCED PROGRAMMING FUNCTIONS

WILL NOT BE DISPLAYED

OPTIONS

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

ADVANCED

PROGRAMMING

"AD"

ADVANCED PROGRAMMING OPTIONS

WILL BE DISPLAYED

NOTE: ADVANCED PROGRAMMING

WILL STAY ENABLED AFTER

EXITING PROGRAMMING UNTIL

THE GATE CYCLES 50 TIMES

FUNCTION

SINGLE INPUT WILL OPEN OPERATOR,

IF OPERATOR IS ALREADY OPEN, SINGLE

INPUT WILL CLOSE OPERATOR

SINGLE INPUT WILL CYCLE OPERATOR
IN ORDER OF OPEN-STOP-CLOSE-STOP

OPTIONS

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

SINGLE BUTTON

INPUT SETUP

"SB"

FUNCTION

SETS THIS OPERATOR FOR

DELAYED OPEN

DISABLES STAGGER FUNCTION

SETS THIS OPERATOR FOR

DELAYED CLOSE

OPTIONS

PRESS UP OR

DOWN TO CYCLE

THROUGH OPTIONS

PRESS ENTER TO

SELECT AN OPTION

STAGGER

MODE

"SM"

DUAL GATES

ONLY

FUNCTION

PRESS ENTER FOR 1 SECOND

WHILE DISPLAY IS FLASHING, PRESS

UP OR DOWN TO CHANGE THE

MAXIMUM RUN TIME (10-99 SECONDS)

OPTIONS

MAXIMUM RUN

TIMER

DISPLAY SHOWS CURRENT

MAXIMUM RUN TIME SETTING

ENTER

PRESS ENTER TO STORE THE VALUE

"RT"

Summary of Contents for TYM 1000







































Search results

Summary of Contents for TYM 1000

Reviews:

Related manuals for TYM 1000

Brands by name

Popular brands

Tymetal Corp. TYM 1000, Installation Manual

Search results

Summary of Contents for TYM 1000

Reviews:

Related manuals for TYM 1000

Brands by name

Popular brands